ABB IRB 1200 Product Manual Download Page 231

Page: 231 / 906

Note

Action

xx1400000754

Apply grease to the cable package, cover all
moving area of the package.

Valid for IRB 1200-5/0.9

Secure the cable package at the bottom of the
housing with cable straps.

Connecting the axis-4 motor connectors

Note

Action

For robots with protection type Clean Room

For robots with food grade lubrication
For robots with protection type Hygienic

Clean the joints that have been opened and wipe
the parts free from particles with spirit on a lint
free.

xx1300002371

Reconnect the motor connectors.

Continues on next page

Product manual - IRB 1200

231

3HAC046983-001 Revision: S

4 Repair

4.3.1 Replacing the main cable package

Continued

Summary of Contents for IRB 1200










































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IRB 1200

Reviews:

ABB IRB 1200, Product Manual, Page: 231 / 906

Search results

Summary of Contents for IRB 1200

Reviews: