ABB IRB 1200 Product Manual Download Page 339

Page: 339 / 906

Note

Action

Guide pin for axis-2 gear unit:
3HAC049704-001

xx1300002562

Fit guide pins to the gearbox.

Always use three guide pins together!

M2 variseal sealing: 3HAC044641-003

xx1400000453

For robots with protection class IP67
For robots with protection type Foundry
Plus

Check the sealing.
Replace if damaged.

CAUTION

Do not fit M2 variseal sealing on robots in
other protection class or protection types.

xx1300002563

Fit the lower arm to the swing, with guid-
ance from the guide pins.

Continues on next page

Product manual - IRB 1200

339

3HAC046983-001 Revision: S

4 Repair

4.4.1 Replacing the lower arm

Continued

Summary of Contents for IRB 1200










































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IRB 1200

Reviews:

ABB IRB 1200, Product Manual, Page: 339 / 906

Search results

Summary of Contents for IRB 1200

Reviews: