ABB IRB 1200 Page 378 Product Manual Download

Page: 378 / 906

Required tools and equipment

Note

Article number

Equipment, etc.

Used to release the motor brakes.

24 VDC power supply

Content is defined in section

Standard

toolkit on page 890

Standard toolkit

Replacing the signal lamp

Note

Action

DANGER

Turn off all:

•

electric power supply

•

hydraulic pressure supply

•

air pressure supply

to the robot, before entering the robot working area.

CAUTION

For robots with protection type Clean Room
For robots with food grade lubrication
For robots with protection type Hygienic

Always cut the paint with a knife and grind the paint
edge when disassembling parts of the robot! See

Cut the paint or surface on the robot before repla-
cing parts on page 158

xx1300000456

Remove the attachment screws of the upper arm
housing cover and lift the cover carefully until the
connectors of the signal lamp can be reached.

Disconnect the connectors and remove the cover
from the robot.

Remove the nut from the lamp and pull out the lamp
from the cover.

Fit the new lamp to the cover and tighten the nut.

Find the lamp connectors in the cable harness in-
side the upper arm housing.

•

Connect lamp connector R3.H1 to cable har-
ness connector H1.

•

Connect lamp connector R3.H2 to cable har-
ness connector H2.

Continues on next page

378

Product manual - IRB 1200

3HAC046983-001 Revision: S

4 Repair

4.4.2 Replacing the signal lamp

Continued

Summary of Contents for IRB 1200










































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IRB 1200

Reviews:

Related manuals for IRB 1200

Brands by name

Popular brands

ABB IRB 1200, Product Manual

Search results

Summary of Contents for IRB 1200

Reviews:

Related manuals for IRB 1200

Brands by name

Popular brands