ABB IRB 1200 Product Manual Download Page 281

Page: 281 / 906

Note

Action

xx1300002391

Remove the connector plate by first removing the
screws.

xx1300002392

Remove the cable housing of the tubular by first
removing the screws.

Note

For robots with protection class IP67
For robots with protection type Foundry Plus
For robots with protection type Hygienic

The frame is glued and needs to be pried off.

Removing the axis-5 FPC unit

Note

Action

DANGER

Make sure that all supplies for electrical power,
hydraulic pressure, and air pressure are turned
off.

CAUTION

For robots with protection type Clean Room
For robots with food grade lubrication
For robots with protection type Hygienic

Always cut the paint with a knife and grind the
paint edge when disassembling parts of the robot!
See

Cut the paint or surface on the robot before

replacing parts on page 158

xx1300002393

Remove the sleeve screws.

Continues on next page

Product manual - IRB 1200

281

3HAC046983-001 Revision: S

4 Repair

4.3.3 Replacing the axis-5 FPC unit

Continued

Summary of Contents for IRB 1200










































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IRB 1200

Reviews:

ABB IRB 1200, Product Manual, Page: 281 / 906

Search results

Summary of Contents for IRB 1200

Reviews: