manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

LS_I2C controller

RM0082

638/844

Doc ID 018672 Rev 1

         

Table 569.

IC_TX_ABRT_SOURCE register bit assignments

Bit

Name

Type

Reset 
value

Description

[31:16]

Reserved

RW

-

Read: undefined. Write: should be zero.

[15]

ABRT_SLVRD_INTX

RW

1’h0

Slave requesting data to transmit.

If set, this bit indicates that the slave is 
requesting data to transmit and the user wrote 
a read command into the transmit FIFO.

[14]

ABRT_SLV_ARBLOST

RW

1’h0

Slave lost the bus.

If set, this bit indicates that the slave lost the 
bus while it was transmitting data to a remote 
master. ARB_LOST bit in this register will be 
set at the same time.

[13]

ABRT_SLVFLUSH_TXFI
FO

RW

1’h0

Slave receive a read command.

If set, this bit indicates that the slave has 
received a read command and some data 
exists in the transmit FIFO, so the slave issues 
a TX_ABRT to flush old data in transmit FIFO.

[12]

ARB_LOST

RW

1’h0

Master lost arbitration.

If set,this bit indicates that either master has 
lost arbitration (

Section 28.4.3

) or, if 

ABRT_SLV_ARBLOST bit in this register is 
also set, the slave transmitter has lost 
arbitration.

[11]

ARB_MASTER_DIS

RW

1’h0

Attempt to use disabled master.

If set, this bit indicates that user attempt to use 
disabled master.

[10]

ABRT_10B_RD_NORST
RT

RW

1’h0

Disable restart and master send a read 
command. If set, this bit indicates that the 
restart is disabled (IC_RESTART_EN bit 
cleared in IC_CON register, 

Section 28.6.3

) 

and the master sends a read command in 10 
bit addressing mode.

[09]

ABRT_SBYTE_ 
NORSTRT

RW

1’h0

Disable restart and user send a start byte. 

If set, this bit indicates that the restart is 
disabled (IC_RESTART_EN bit cleared in 
IC_CON register, 

Section 28.6.3

) and the user 

is trying to send a start byte.

[08]

ABRT_HS_ NORSTRT

RW

1’h0

Disable restart and user try to use master to 
send data. 

If set, this bit indicates that the restart is 
disabled (IC_RESTART_EN bit cleared in 
IC_CON register, 

Section 28.6.3

) and the user 

is trying to use the master to send data in high-
speed mode.

[07]

ABRT_SBYTE_ACKDET

RW

1’h0

Master sent an acknowledge start byte. 

If set, this bit indicates that the master has sent 
a start byte which was acknowledged (wrong 
behavior).

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

Magicfx FX-COMM4NDER MFX3203 User And Installation Manual preview
FX-COMM4NDER MFX3203
Бренд: Magicfx Страницы: 16
Frico ERP Instruction Manual preview
ERP
Бренд: Frico Страницы: 12
Abov A96G140 User Manual preview
A96G140
Бренд: Abov Страницы: 278
Zennio MAXinBOX66 Technical Documentation preview
MAXinBOX66
Бренд: Zennio Страницы: 2
FAAC RESIST TPS SA Manual preview
RESIST TPS SA
Бренд: FAAC Страницы: 3
SSHC TSSHC-3IL-24 Quick Start Manual preview
TSSHC-3IL-24
Бренд: SSHC Страницы: 2
Knoll VC220PMI Installation Instructions preview
VC220PMI
Бренд: Knoll Страницы: 2
Oase StreamMax Pump Controller Operating Instructions Manual preview
StreamMax Pump Controller
Бренд: Oase Страницы: 142
DELTA DORE TYBOX 1010 WT User Manual preview
TYBOX 1010 WT
Бренд: DELTA DORE Страницы: 9
Work Pro WAC 7 User Manual preview
WAC 7
Бренд: Work Pro Страницы: 9
Unitech UT-102 Instruction Manual preview
UT-102
Бренд: Unitech Страницы: 15
Balmar Max Charge MC-614-H Installation And Operation Manual preview
Max Charge MC-614-H
Бренд: Balmar Страницы: 20
Bernard Controls AQ Logic Series Startup Manual preview
AQ Logic Series
Бренд: Bernard Controls Страницы: 88
Allen-Bradley ProcessLogix 1757-PLX52 Installation Instructions Manual preview
ProcessLogix 1757-PLX52
Бренд: Allen-Bradley Страницы: 24
TRIAC THD S11 SERIES Installation & Maintenance Manual preview
THD S11 SERIES
Бренд: TRIAC Страницы: 7
Gira 0425 00 Quick Start Manual preview
0425 00
Бренд: Gira Страницы: 7
Knoll MR173 Installation And Operating Instructions preview
MR173
Бренд: Knoll Страницы: 3
YASKAWA U1000 iQpump Drive Technical Manual preview
U1000 iQpump Drive
Бренд: YASKAWA Страницы: 706

Бренды по названию

Популярные бренды

Загрузить еще бренды