STMicroelectronics SPEAr300 Скачать руководство пользователя страница 195 | Manualshive

Страница: 195 / 844

background image

RM0082

DDR memory controller (MPMC)

Doc ID 018672 Rev 1

out_of_range_type [1:0]

Holds the type of command that caused an out-of-range interrupt
request to the memory devices. This parameter is read-only.

For more information on out-of-range address checking, refer to

Section 10.8 on page 140

placement_en [0]

Enables using the placement logic to fill the command queue.

1‘b0 - Placement logic is disabled. The command queue is a straight
FIFO.

1‘b1 - Placement logic is enabled. The command queue will be filled
according to the placement logic factors.

power_down [0]

When this parameter is set to 1'b1, the Memory Controller will complete
processing of the current burst for the current transaction (if any), issue
a pre-charge all command and then disable the clock enable signal to
the DRAM devices. Any subsequent commands in the command queue
will be suspended until this parameter is set to 1'b0.

1'b0 - Enable full power state.

1'b1 - Disable the clock enable and power down the Memory Controller.

priority_en [0]

Controls priority as a condition when using the placement logic to fill the
command queue.

1'b0 - Disabled

1'b1 - Enabled

pwrup_srefresh_exit [0]

Controls controller to exit power-down mode by executing a self-refresh
instead of the full memory initialization.

1'b0 - Disabled

1'b1 - Enabled

q_fullness [3:0]

Defines quantity of data that will be considered full for the command
queue.

rd2rd_turn [0]

Adds an additional clock between back-to-back READ operations to
different chip selects. The extra clock is required for mobile DDR
devices where:

tac_max > (period/2+tac_min)

Without this additional clock, the first READ may drive DQS out at
tac_max and the second READ may drive DQS out at tac_min,
resulting in a contention on the DQS line.

1'b0 - Disabled

1'b1 - Enabled

reduc [0]

Controls the width of the memory datapath. When enabled, the upper
half of the memory buses (DQ, DQS and DM) are unused and relevant
data only exists in the lower half of the buses. This parameter expands
the Memory Controller for use with memory devices of the configured
width or half of the configured width.

For more information on half datapath mode, refer to

Section 10.8 on

.

1'b0 - Standard operation using full memory bus.

1'b1 - Memory datapath width is half of the maximum size.

Table 153.

Memory controller parameters (continued)

Parameter

Description

«
...
193
194
195
196
197
...
»

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

Бренд: ABB Страницы: 139

Бренд: ABB Страницы: 28

Бренд: ABB Страницы: 59

Бренд: Hach Страницы: 2

Бренд: Hach Страницы: 12

Бренд: Hach Страницы: 472

Бренд: Hach Страницы: 64

Бренд: Hach Страницы: 210

Бренд: ICM Controls Страницы: 2

Бренд: ICM Controls Страницы: 2

Бренд: ZKTeco Страницы: 2

Бренд: Rheem Страницы: 2

Бренд: Maintronic Страницы: 53

Бренд: Altera Страницы: 59

Бренд: Datakom Страницы: 34

Бренд: Hotone Страницы: 2

Бренд: Infineon Technologies Страницы: 677

Бренд: Murphy Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды