manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

HS_USB2.0 host

RM0082

448/844

Doc ID 018672 Rev 1

HcInterruptEnable register. Thus, writing a '1' to a bit in this register clears the 
corresponding bit in the HcInterruptEnable register, whereas writing a '0' to a bit in this 
register leaves the corresponding bit in the HcInterruptEnable register unchanged. On read, 
the current value of the HcInterruptEnable register is returned.

Table 371.

HcInterruptDisable register bit assignments

22.6.31 

Memory pointer partition

22.6.32 HcHCCA 

register

The HcHCCA register contains the physical address of the Host Controller Communication 
Area. The Host Controller Driver determines the alignment restrictions by writing all 1s to 
HcHCCA and reading the content of HcHCCA. The alignment is evaluated by examining the 
number of zeroes in the lower order bits. The minimum alignment is 256 bytes; therefore, 
bits 0 through 7 must always return '0' when read. Detailed description can be found in 
Chapter 4. This area is used to hold the control structures and the Interrupt table that are 
accessed by both the Host Controller and the Host Controller Driver.

Bits

Name

Reset

Read/Write

Description

HCD

HC

[31]

MIE

0b

R/W

R

A ‘0’ written to this field is ignored by HC. A '1' written to 
this field disables interrupt generation due to events 
specified in the other bits of this register. This field is set 
after a hardware or software reset.

[30]

OC

0b

R/W

R

0 - Ignore

1 - disable interrupt generation due to Ownership Change.

[29:07]

Reserved

[06]

RHSC

0b

R/W

R

0 - Ignore

1 - disable interrupt generation due to Root Hub Status 
Change.

[05]

FNO

0b

R/W

R

0 - Ignore

1 - disable interrupt generation due to Frame Number 
Overflow.

[04]

UE

0b

R/W

R

0 - Ignore

1 - disable interrupt generation due to Unrecoverable 
Error.

[03]

RD

0b

R/W

R

0 - Ignore

1 - disable interrupt generation due to Resume Detect.

[02]

SF

0b

R/W

R

0 - Ignore

1 - disable interrupt generation due to Start of Frame.

[01]

WDH

0b

R/W

R

0 - Ignore

1 - disable interrupt generation due to HcDoneHead 
Writeback.

[00]

SO

0b

R/W

R

0 - Ignore

1 - disable interrupt generation due to Scheduling 
Overrun.

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

Parker ER Series Maintenance Instructions & Parts List preview
ER Series
Бренд: Parker Страницы: 44
Yamaha CEmarking RCX221 User Manual preview
CEmarking RCX221
Бренд: Yamaha Страницы: 468
Zamel ROW-01 Quick Manual preview
ROW-01
Бренд: Zamel Страницы: 2
D+H RZN 4402-K V2 Original Instructions Manual preview
RZN 4402-K V2
Бренд: D+H Страницы: 32
Eaton EZD Series User Manual preview
EZD Series
Бренд: Eaton Страницы: 448
POLA HP49 Handbook preview
HP49
Бренд: POLA Страницы: 2
YASKAWA J1000 CIMR-JC series Option Manual preview
J1000 CIMR-JC series
Бренд: YASKAWA Страницы: 26
EBS CPX200NB Installation And Programming Manual preview
CPX200NB
Бренд: EBS Страницы: 116
Daikin BRC1H62W Operation Handbook preview
BRC1H62W
Бренд: Daikin Страницы: 2
Leviton GreenMax DRC DRC07-ED0 Quick Start Manual preview
GreenMax DRC DRC07-ED0
Бренд: Leviton Страницы: 2
A & H AMFLOW A2-ACM Installation, Operation & Service Manual preview
AMFLOW A2-ACM
Бренд: A & H Страницы: 35
MegaLite MEMO CORE CONTROL User Manual preview
MEMO CORE CONTROL
Бренд: MegaLite Страницы: 11
Brooks 5866 Installation And Operation Manual preview
5866
Бренд: Brooks Страницы: 66
Leader F1620 Manual preview
F1620
Бренд: Leader Страницы: 46
SSHC TSSHC-3IL-24 Quick Start Manual preview
TSSHC-3IL-24
Бренд: SSHC Страницы: 2
TA SMS14U Manual preview
SMS14U
Бренд: TA Страницы: 4
Heinzmann HELENOS V DC 2005DP.2-01 Manual preview
HELENOS V DC 2005DP.2-01
Бренд: Heinzmann Страницы: 66
Kapego LED R-DMX 3+1 Manual preview
R-DMX 3+1
Бренд: Kapego LED Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды