manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

RM0082

RS_Flexible static memory controller (FSMC)

Doc ID 018672 Rev 1

665/844

Note:

Multiple chip enable pins allow to connect up to four different memory devices
simultaneously. Address and data buses are shared. Controller performs only one access at
a time.

31.4.2 Address 

map

The address space for FSMC is further divided as follows:

         

Note:

CL and AL signals for NAND Flash correspond to A16 and A17, respectively on FSMC. So,
if we write at an address within the address range of a particular NAND bank such that the
address bit 16/17 is '1', the CL/AL  pin at output will go high. Data on data lines is thus
interpreted as command and address respectively. 

31.4.3 Register 

map

The FSMC can be fully configured by programming its 32-bit wide registers which can be
accessed at the base address 0x9400_0000.

Independent configuration registers are associated with each chip select, and they allow to
specify the type of external device (SRAM or Flash) as well as the associated timings (i.e.,
how many HCLK cycles to complete a transaction), and other external device characteristics
so that FSMC can use the correct protocol. 

Table 593.

NAND Flash

Signal

Direction

Description

D[15:0]

Bidir

Data lines.

CL

Out

Command Latch Enable Active High.

AL

Out

Address Latch Enable Active High.

/W

Out

Write Enable Active Low.

/R

Out

Read Enable Active Low.

/E1, /E2, /E3 and /E4

Out

Chip Enable Active Low.

R/B

In

Wait Signal Active Low.

Table 594.

FSMC Address Map

From

To

Description

0x8000_0000

0x83FF_FFFF

NAND on Bank0

0x8400_0000

0x87FF_FFFF

NAND on Bank1

0x8800_0000

0x8BFF_FFFF

NAND on Bank2

0x8C00_0000

0x8FFF_FFFF

NAND on Bank3

0x9000_0000

0x90FF_FFFF

NOR/SRAM on Bank0

0x9100_0000

0x91FF_FFFF

NOR/SRAM on Bank1

0x9200_0000

0x92FF_FFFF

NOR/SRAM on Bank2

0x9300_0000

0x93FF_FFFF

NOR/SRAM on Bank3

0x9400_0000

0x98FF_FFFF

FSMC Configuration Registers

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

Panasonic FP-I4C User Manual preview
FP-I4C
Бренд: Panasonic Страницы: 31
Panasonic EYFR03 Training Manual preview
EYFR03
Бренд: Panasonic Страницы: 31
NAiS FP Series Hardware Manual preview
FP Series
Бренд: NAiS Страницы: 199
Panasonic CZ-ANC2 Instruction Manual preview
CZ-ANC2
Бренд: Panasonic Страницы: 38
Panasonic CZ-256ESMC3 Quick Reference preview
CZ-256ESMC3
Бренд: Panasonic Страницы: 36
Panasonic CZ-256ESMC3 Technical Data Manual preview
CZ-256ESMC3
Бренд: Panasonic Страницы: 179
Panasonic AW-RP60G Operating Manual preview
AW-RP60G
Бренд: Panasonic Страницы: 23
ZKTeco F6 Installation Manual preview
F6
Бренд: ZKTeco Страницы: 2
FASAR ELETTRONICA FE230 Quick Start Manual preview
FE230
Бренд: FASAR ELETTRONICA Страницы: 2
Faro 33928 Installation Manual preview
33928
Бренд: Faro Страницы: 3
YASKAWA G7 Series Technical Manual preview
G7 Series
Бренд: YASKAWA Страницы: 456
Eaton LS Series Instruction Leaflet preview
LS Series
Бренд: Eaton Страницы: 2
nekos SKY 650 Manual For Installation And User Manual preview
SKY 650
Бренд: nekos Страницы: 8
nekos SKY 450 Installation And Use Manual preview
SKY 450
Бренд: nekos Страницы: 8
TEL AFA4000/1/AS Installation And Calibration Manual preview
AFA4000/1/AS
Бренд: TEL Страницы: 26
Vimar EAM6 Installation And Operation Manual preview
EAM6
Бренд: Vimar Страницы: 32
Swagelok BSH 10 Series User Manual preview
BSH 10 Series
Бренд: Swagelok Страницы: 20
TECH EU-391 ZPID User Manual preview
EU-391 ZPID
Бренд: TECH Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды