manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

RS_Reconfigurable array subsystem (RAS) registers

RM0082

660/844

Doc ID 018672 Rev 1

30.5 RAS 

Interrupt 

assignments

         

[27:24]

4’h0

These bits are used for dynamic selection of NAND or NOR on each bank of 
FSMC. Each bit corresponds to a bank of FSMC. For e.g.

Bit24 corresponds to Bank0

Bit25 corresponds to Bank1 and so on…

If the bit is set i.e. '1' - NOR

If the bit is clear i.e.

'0' - NAND

[23]

1’h0

This bit is used to select between lower and higher numbered G8/G10 sets in 
modes where they are duplicated.

In output mode, both sets of G8/G10 provide output data.

In input mode, if this bit is 0, lower numbered G8/G10 set is active. If this bit is 
1, higher numbered G8/G10 set is active.

[22:05]

18’h0

Reserved

[04]

1’h0

Determines if TDM_DOUT is available at Pin61

'1'- TDM_DOUT on Pin61

'0'- SPI_I2C7 on Pin61

[03:00]

4’h0

Selects different MODES as below:

– 0000 NAND

– 0001 NOR

– 0010 PHOTO_FRAME

– 0011 LEND_IP_PHONE

– 0100 HEND_IP_PHONE

– 0101 LEND_WIFI_PHONE

– 0110 HEND_WIFI_PHONE

– 0111 ATA_PABX_wI2S

– 1000 ATA_PABX_I2S

– 1100 CAM1_LCDw

– 1101 CAMu_LCD

– 1110 CAMu_LCDw

– 1111 CAM1_LCD

Table 589.

RAS Register 2 description (continued)

Field

Default 
Value

Description

Table 590.

RAS Interrupt assignment

Generic RAS 
Interrupt 

VIC

IPs

4

1

SDIO

3

30

CLCD

2

29

Reserved

1

28

TELECOM

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

GE PACSystems* RX3i Application Manual preview
PACSystems* RX3i
Бренд: GE Страницы: 39
GE PACSystems* RX3i Secure Deployment Manual preview
PACSystems* RX3i
Бренд: GE Страницы: 35
GE PACSystems* RX3i Important Product Information preview
PACSystems* RX3i
Бренд: GE Страницы: 3
GE PACSystems* RX3i User Manual preview
PACSystems* RX3i
Бренд: GE Страницы: 169
e-BLEACH infinity User Manual preview
infinity
Бренд: e-BLEACH Страницы: 24
ZKTeco F6 Installation Manual preview
F6
Бренд: ZKTeco Страницы: 2
FASAR ELETTRONICA FE230 Quick Start Manual preview
FE230
Бренд: FASAR ELETTRONICA Страницы: 2
Faro 33928 Installation Manual preview
33928
Бренд: Faro Страницы: 3
YASKAWA G7 Series Technical Manual preview
G7 Series
Бренд: YASKAWA Страницы: 456
York CIW01 Installation & Maintenance Manual preview
CIW01
Бренд: York Страницы: 24
Desoutter 6159326760 Original Instructions Manual preview
6159326760
Бренд: Desoutter Страницы: 74
Samson 3371 Series Mounting And Operating Instructions preview
3371 Series
Бренд: Samson Страницы: 70
BQT BioX Series Installation Manual preview
BioX Series
Бренд: BQT Страницы: 2
TSM DOUBLER2 Instructions For Installing preview
DOUBLER2
Бренд: TSM Страницы: 2
ICP DAS USA ALM-04-MRTU User Manual preview
ALM-04-MRTU
Бренд: ICP DAS USA Страницы: 26
National Instruments cRIO-FRC II User Manual And Specifications preview
cRIO-FRC II
Бренд: National Instruments Страницы: 22
Variotech ENA3 Manual preview
ENA3
Бренд: Variotech Страницы: 24
Lennox HYDROCONTROL Installation, Operating And Maintenance Manual preview
HYDROCONTROL
Бренд: Lennox Страницы: 34

Бренды по названию

Популярные бренды

Загрузить еще бренды