manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

RS_SDIO controller

RM0082

714/844

Doc ID 018672 Rev 1

32.7.16 SWRES 

register 

The SWRES bit assignments are given in 

Table 635

.

         

Table 635.

SWRES register bit assignments

Bit

Name

Reset 
value

Type

Description

[07:03]

-

-

Rsvd

Reserved

[02]

SWRESDAT

-

RWAC

Only part of data circuit is reset. The following
registers and bits are cleared by this bit: 

Buffer Data Port Register

Buffer is cleared and Initialized.

Present State register

Buffer read Enable / Buffer write Enable

Read Transfer Active

Write Transfer Active

DAT Line Active

Command Inhibit (DAT)

Block Gap Control register

Continue Request

Stop At Block Gap Request

Normal Interrupt Status register

Buffer Read Ready

Buffer Write Ready

Block Gap Event

Transfer Complete

1’b1 - Reset

1’b0 - Work

[01]

SWRESCMD -

RWAC

Only part of command circuit is reset. The following
registers and bits are cleared by this bit:

Present State register

Command Inhibit (CMD)

Normal Interrupt Status register

Command Complete

1’b1 - Reset

1’b0 - Work

[00]

SWRESALL

-

RWAC

This reset affects the entire HC except for the card
detection circuit. Register bits of type ROC, RW,
RW1C, RWAC are cleared to logic ‘0’. During its
initialization, the HD shall set this bit to logic ‘1’ to
reset the HC. The HC shall reset this bit to logic ‘0’
when capabilities registers are valid and the HD can
read them. Additional use of Software Reset For All
may not affect the value of the Capabilities registers. If
this bit is set to 1, the SD card shall reset itself and
must be re initialized by the HD.

1’b1 - Reset

1’b0 - Work

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

Oceanic ZX Service Procedure preview
ZX
Бренд: Oceanic Страницы: 13
Warren Controls 313 Installation, Operation & Maintenance Instructions Manual preview
313
Бренд: Warren Controls Страницы: 16
Banner SC22-3 Quick Start Manual preview
SC22-3
Бренд: Banner Страницы: 15
Watts 009 Series Instruction, Installation, Maintenance And Repair Manual preview
009 Series
Бренд: Watts Страницы: 24
Grundfos EC 15 Installation And Operating Instructions Manual preview
EC 15
Бренд: Grundfos Страницы: 80
Velleman CHLSC2 User Manual preview
CHLSC2
Бренд: Velleman Страницы: 22
National Instruments NI 9683 User Manual And Specifications preview
NI 9683
Бренд: National Instruments Страницы: 27
Evco EVCLC229N9E Manual preview
EVCLC229N9E
Бренд: Evco Страницы: 78
Pro-face LT-4201TM Installation Manual preview
LT-4201TM
Бренд: Pro-face Страницы: 48
Nuvation BMS NUV100-CI-12 Installation Manual preview
BMS NUV100-CI-12
Бренд: Nuvation Страницы: 41
National Instruments NI cRIO-9053 User Manual preview
NI cRIO-9053
Бренд: National Instruments Страницы: 100
VECTOR CONTROLS TCX2 Product Data Sheet preview
TCX2
Бренд: VECTOR CONTROLS Страницы: 10
National Instruments AMUX-64T Installation Manual preview
AMUX-64T
Бренд: National Instruments Страницы: 3
Kelly KLS14801-8080N User Manual preview
KLS14801-8080N
Бренд: Kelly Страницы: 43
Zareba LIS10 User Manual preview
LIS10
Бренд: Zareba Страницы: 40
Team Orion Vortex R10 One Instruction Manual preview
Vortex R10 One
Бренд: Team Orion Страницы: 28
Inverter sMove s4 AP Instructions preview
sMove s4 AP
Бренд: Inverter Страницы: 2
Tripp Lite NetController B042-004 Specifications preview
NetController B042-004
Бренд: Tripp Lite Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды