manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

RM0082

RS_Telecom IP

Doc ID 018672 Rev 1

785/844

RESET: all ‘0’

Table 704.

TDM_conf register (Offset 0x04)

Bits

Name

Comments

[31]

LBio

loopback from DIN to DOUT (external)

when LBio = ‘0’ 

no loopback is implemented

when LBio = ‘1’

 DOUT plays back the DIN value

[30]

LBoi

loopback from DOUT to DIN

when LBio = ‘0’ 

no loopback is implemented

when LBio = ‘1’ 

DIN receives the DOUT value

[29]

LBshio

loopback from shift_in register to shift_out register (external)

when LBshio =’0’ 

no loopback is implemented

when LBShio = ‘1’ 

DOUT plays back the DIN value delayed by one 

byte.

[28]

LBSD

loopback from selected data (sw_data_out or buf_data_out to 
store_in register

when LBSD = ‘0’

 no loopback is implemented

when LBSD = ‘1’ 

the selected data is sent to the memories (sw or 

buf) through store_in.

[27]

LBPD

loopback from parallel data (sw_data_out to sw_data_in and 
buf_data_out to buf_data_in)

When LBPD = ‘0’ 

no loopback is implemented

When LBPD = ‘1’ 

the loopback is set from incoming data from 

memory to outgoing data to memory, both for sw and buf channels. 
sw_data_out is sent to sw_data_in and buf_data_out is sent to 
buf_data_in.

[26]

ACT

activates the int_CLK clock that is sent to all other blocks. This 
initialization is mandatory when using any telecom function

ACT = ‘0’:

 int_CLK is always 0.

ACT = ‘1’:

 int_CLK is either the generated internal clock or the slave 

external clock.

[25:24]

CLK

these bits select what is output on the pins according to the 
following table:

CLKo1-0

PL_Clk2

PL_Clk3

00

0

0

01

Int_CLK

0

10

Int_CLK

/int_CLK

11

Int_CLK

Internal_clock

[23:22]

MIIC

selects the clock to be output on PL_CLK1 according to the 
following table:

MIIC

PL_Clk1

10

ClkR_Pll2

11

ClkR_Synt(3)

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

RadioMaster MT12 Quick Start Manual preview
MT12
Бренд: RadioMaster Страницы: 10
Wavelength Electronics PTC5000 Datasheet And Operating Manual preview
PTC5000
Бренд: Wavelength Electronics Страницы: 17
FASTRON. FTM1 Series User Manual preview
FTM1 Series
Бренд: FASTRON. Страницы: 37
Festo MPAL-VI Original Instructions preview
MPAL-VI
Бренд: Festo Страницы: 2
HIKVISION DS-PTA-WL-868 User Manual preview
DS-PTA-WL-868
Бренд: HIKVISION Страницы: 5
Nexen RSTC1000 User Manual preview
RSTC1000
Бренд: Nexen Страницы: 28
Allen-Bradley Kinetix 350 User Manual preview
Kinetix 350
Бренд: Allen-Bradley Страницы: 162
PXM Driver LED 1x2A/48V Manual preview
Driver LED 1x2A/48V
Бренд: PXM Страницы: 11
M-Audio Keystation 61es User Manual preview
Keystation 61es
Бренд: M-Audio Страницы: 15
Webasto Thermo Call TC3 Installation Instructions Manual preview
Thermo Call TC3
Бренд: Webasto Страницы: 15
Zapi ADPZP0CC User Manual preview
ADPZP0CC
Бренд: Zapi Страницы: 36
Aqua Lung Legend LX Second Stage Technical Maintenance Manual preview
Legend LX Second Stage
Бренд: Aqua Lung Страницы: 18
A.O. Smith INTELLI-VENT Troubleshooting Manual preview
INTELLI-VENT
Бренд: A.O. Smith Страницы: 46
Phocos CIS05-2L User Manual preview
CIS05-2L
Бренд: Phocos Страницы: 2
Jakka EVO PH Manual preview
EVO PH
Бренд: Jakka Страницы: 31
Carrera GO!!! Plus Operating Instructions preview
GO!!! Plus
Бренд: Carrera Страницы: 3
Allen-Bradley Compact GuardLogix 5370 User Manual preview
Compact GuardLogix 5370
Бренд: Allen-Bradley Страницы: 210
NI PXI-8105 Installation Manual preview
PXI-8105
Бренд: NI Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды