manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

RM0082

BS_Watchdog timer

Doc ID 018672 Rev 1

317/844

16.5.7 WdogRIS 

register

The WdogRIS (raw interrupt status) is a RO register indicates the raw interrupt status from 
the counter (before masking by WdogControl register). The WdogRIS bit assignments are 
given in 

Table 250

.

         

16.5.8 WdogMIS 

register

The WdogMIS (masked interrupt status) is a RO register indicates the masked interrupt 
status from the counter (after masking by the Wdogcontrol register). The WdogMIS bit 
assignments are given in 

Table 251

.

         

16.5.9 WdogLock 

register

The WdogLock is a RW register allows to enable/disable write-access to all other registers. 
This is to prevent software from disabling the Watchdog module operation. The WdogLock 
bit assignments are given in 

Table 252

.

         

Table 250.

WdogRIS register bit assignments

Bit

Name

Reset value

Description

[31:01]

Reserved

-

Read: undefined.

[00]

WDOGRIS

1’h0

If set, it indicates that an interrupt has been raised by the 
Watchdog counter reaching zero.

Table 251.

WdogMIS register bit assignments

Bit

Name

Reset value

Description

[31:01]

Reserved

-

Read: undefined.

[00]

WDOGMIS

1’h0

Masked interrupt status.

The value of this bit is the logical AND of the raw interrupt 
status (WDOGRIS bit of the WdogRIS register) with the 
INTEN bit of the WdogControl register.,It is the same value 
that is passed to the interrupt output of the Watchdog 
module.

Table 252.

WdogLock register bit assignments

Bit

Name

Reset value

Description

[31:01]

WDOGLOCK

32’h0

Write access enable.

Writing 32‘h1ACCE551 to this register enables write 
access to all other registers. Writing any other value 
disables write access to all other registers. 

A read from this register returns the lock status rather than 
the actual value:

32‘h00000000 = Write access to all others registers is 
enabled (not locked). 

32‘h00000001 = Write access to all others registers is 
disabled (locked).

[00]

Reserved

-

Read: undefined.

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

OEG KMS Manual preview
KMS
Бренд: OEG Страницы: 168
RadioMaster POCKET Quick Start Manual preview
POCKET
Бренд: RadioMaster Страницы: 10
HANYOUNG NUX TS500 Manual preview
TS500
Бренд: HANYOUNG NUX Страницы: 56
OJ Electronics EFR Series Instructions Manual preview
EFR Series
Бренд: OJ Electronics Страницы: 8
OJ Electronics ETO2 Manual preview
ETO2
Бренд: OJ Electronics Страницы: 112
OJ EFS Series Instructions Manual preview
EFS Series
Бренд: OJ Страницы: 17
Parkside PDWE 8 A2 Operation And Safety Notes Translation Of The Original Instructions preview
PDWE 8 A2
Бренд: Parkside Страницы: 65
Eaton CDAU-01/04 Instruction Leaflet preview
CDAU-01/04
Бренд: Eaton Страницы: 4
Zero 88 Chilli Master Operating Manual preview
Chilli Master
Бренд: Zero 88 Страницы: 34
Danfoss MCD 600 Installation Manual preview
MCD 600
Бренд: Danfoss Страницы: 22
cnsat Smart Antenna Selector Instruction Manual preview
Smart Antenna Selector
Бренд: cnsat Страницы: 14
Parker COMPAX 02 Series User Manual preview
COMPAX 02 Series
Бренд: Parker Страницы: 242
Danfoss EKC 531D1 Instructions Manual preview
EKC 531D1
Бренд: Danfoss Страницы: 18
Zapi SEM-Zero Manual preview
SEM-Zero
Бренд: Zapi Страницы: 39
Licht-Technik Mix4-6 Functional Description preview
Mix4-6
Бренд: Licht-Technik Страницы: 13
M5Stack FIRE Quick Start Manual preview
FIRE
Бренд: M5Stack Страницы: 6
Spektrum FC6250HX Manual preview
FC6250HX
Бренд: Spektrum Страницы: 20
Cumberland Smart-Flex FLX-4629 Operation Instructions Manual preview
Smart-Flex FLX-4629
Бренд: Cumberland Страницы: 30

Бренды по названию

Популярные бренды

Загрузить еще бренды