manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

RM0082

AS_Cryptographic co-processor (C3)

Doc ID 018672 Rev 1

371/844

21.6.10 

Memory base address register (HIF_MBAR)

The Base Address of the Internal Memory can be programmed to any multiple of 64 KB. Bits 
31-16 of MBAR are used for this. Channel and Instruction Dispatcher transactions that fall 
within a window of 64 KB starting from MBAR are then routed to the Internal Memory (if 
enabled). The Internal Memory Base Address can be changed at any time but behavior of 
the active transactions done in this range is undefined. The Byte Bucket has priority if its 
Base Address (NBAR) is programmed with the same value as MBAR.

         

         

         

         

21.6.11 

Memory control register (HIF_MCAR)

The Internal Memory must be enabled to allow Channels and Instruction Dispatchers to 
access it. This is done using the Enable Memory Mapping bit (EMM). The correct procedure 
for the Software to enable the Internal Memory is to first program its base address using 
HIF_MBAR and then enable it by setting the EMM bit of HIF_MCR. The Internal Memory 
can be enabled or disabled at any time but the behaviour of the active transactions done in 
this range is undefined.

Normally, when using the Address and Data registers pair (HIF_MAAR and HIF_MDAR) to 
access Internal Memory locations from AHB, the Address register is auto incremented. To 
disable this feature Disable Auto Increment on Read and Disable Auto Increment Write bits 
(DAIR and DAIW) are offered.

Bit

31

30

29

28

27

26

25

24

Symbol

B31

B30

B29

B28

B27

B26

B25

B24

Initial Value

0

0

0

0

0

0

0

0

Type

R/W

R/W

R/W

R/W

R/W

R/W

R/W

R/W

Bit

23

22

21

20

19

18

17

16

Symbol

B23

B22

B21

B20

B19

B18

B17

B16

Initial Value

0

0

0

0

0

0

0

0

Type

R/W

R/W

R/W

R/W

R/W

R/W

R/W

R/W

Bit

15

14

13

12

11

10

9

8

Symbol

-

-

-

-

-

-

-

-

Initial Value

0

0

0

0

0

0

0

0

Type

RO

RO

RO

RO

RO

RO

RO

RO

Bit

7

6

5

4

3

2

1

0

Symbol

-

-

-

-

-

-

-

-

Initial Value

0

0

0

0

0

0

0

0

Type

RO

RO

RO

RO

RO

RO

RO

RO

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

H3C WX5500H series User Configuration Manual preview
WX5500H series
Бренд: H3C Страницы: 57
Hach sc200 Software Update preview
sc200
Бренд: Hach Страницы: 2
Hach ORBISPHERE 410 Quick Operator'S Manual preview
ORBISPHERE 410
Бренд: Hach Страницы: 12
Hach AS950 AWRS Basic Operations preview
AS950 AWRS
Бренд: Hach Страницы: 472
Hach sc1000 User Manual preview
sc1000
Бренд: Hach Страницы: 64
Hach SC4500 Basic User Manual preview
SC4500
Бренд: Hach Страницы: 210
Samson 2479 Mounting And Operating Instructions preview
2479
Бренд: Samson Страницы: 78
Magnescale LY71 Manual preview
LY71
Бренд: Magnescale Страницы: 3
NCR MSR Instructions Manual preview
MSR
Бренд: NCR Страницы: 8
Eaton FC18 User Manual preview
FC18
Бренд: Eaton Страницы: 10
YASKAWA CIMR-ZU Series Programming Manual preview
CIMR-ZU Series
Бренд: YASKAWA Страницы: 340
PENGWYN 485-1P-JS Technical Manual preview
485-1P-JS
Бренд: PENGWYN Страницы: 32
Warner Electric CBC-801-1 Installation Instructions And Service Manual preview
CBC-801-1
Бренд: Warner Electric Страницы: 6
Altronix Trove T1VK3F4 Installation Manual preview
Trove T1VK3F4
Бренд: Altronix Страницы: 8
nvent JBS-100-EC Installation Instructions Manual preview
JBS-100-EC
Бренд: nvent Страницы: 6
Teledyne THCD-401 Instruction Manual preview
THCD-401
Бренд: Teledyne Страницы: 47
Western Co WMarine10 Technical Manual preview
WMarine10
Бренд: Western Co Страницы: 14
Cypress CY3643 Quick Start Manual preview
CY3643
Бренд: Cypress Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды