manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

RM0082

DDR memory controller (MPMC)

Doc ID 018672 Rev 1

191/844

enable_quick_srefresh [0]

When this bit is set, the memory initialization sequence will be 
interrupted and self-refresh mode will be entered.

1'b0 - Continue memory initialization.

1'b1 - Interrupts memory initialization and enter self-refresh mode.

fast_write [0]

Controls the mode and timing the WRITE commands are issued toward 
the DRAM devices.

1'b0 - The Memory Controller will issue a WRITE command to the 
DRAM devices as it has received enough data for one DRAM burst. In 
this mode, WRITE data can be sent in any cycle relative to the WRITE 
command. This mode also allows multi-word WRITE command data to 
arrive in non-sequential cycles.

1'b1 - The Memory Controller will issue a WRITE command to the 
DRAM devices after the first word of the WRITE data is received by the 
Memory Controller. The first word can be sent at any time relative to the 
WRITE command. In this mode, multi-word WRITE command data 
must be available to the Memory Controller in sequential cycles.

initaref [3:0]

Defines the number of auto-refresh commands needed by the DRAM 
devices to satisfy the initialization sequence.

int_ack [5:0]

Sets the clearing of the int_status parameter.

If any of the int_ack bits are set to 'b1 the corresponding bit in the 
int_status parameter will be set to 'b0. Any int_ack bits set to 1'b0 does 
not affect the corresponding bit in the int_status parameter. This 
parameter will always read back as “0”.

int_mask [6:0]

Active-high mask bits that control the value of the Memory controller_int 
signal on the Memory Controller interface. This mask is inverted and 
then logically AND'ed with the outputs of the int_status parameter.

int_status [6:0]

Reports the status of all possible interrupts generated by the Memory 
Controller. The MSB is the result of a logical OR of all the lower bits. 
This parameter is read-only.

The int_status bits correspond to these interrupts:

Bit 0 - A single access outside the defined PHYSICAL memory space 
detected.

Bit 1 - Multiple accesses outside the defined PHYSICAL memory space 
detected.

Bit 2 - DRAM initialization complete.

Bit 3 - Address cross page boundary detected.

Bit 4 - Both DDR2 and Mobile modes have been enabled.

Bit 5 - DLL unlock condition detected.

Bit 6 - Logical OR of all other bits.

intrptapburst [0]

Controls whether an interruption of an auto pre-charge command, by 
another command for a different bank, is allowed.

If enabled, the current operation will be interrupted.

However, the bank will be pre-charged as if the current operation were 
allowed to continue.

1'b0 - Interrupt Disable.

1'b1 - Interrupt Enable.

Table 153.

Memory controller parameters (continued)

Parameter

Description

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

Particle B Series Quick Start Manual preview
B Series
Бренд: Particle Страницы: 6
LAE electronic LF28 Instructions For Installation And Use Manual preview
LF28
Бренд: LAE electronic Страницы: 7
LAE electronic AT1-5 Instructions For Use preview
AT1-5
Бренд: LAE electronic Страницы: 2
RAM RP2000 User Manual preview
RP2000
Бренд: RAM Страницы: 71
ZKTeco IN710 Quick Start Manual preview
IN710
Бренд: ZKTeco Страницы: 11
Altronix Trove T1VK3F4 Installation Manual preview
Trove T1VK3F4
Бренд: Altronix Страницы: 8
nvent JBS-100-EC Installation Instructions Manual preview
JBS-100-EC
Бренд: nvent Страницы: 6
Teledyne THCD-401 Instruction Manual preview
THCD-401
Бренд: Teledyne Страницы: 47
Western Co WMarine10 Technical Manual preview
WMarine10
Бренд: Western Co Страницы: 14
Webasto SmarTemp Control fx Installation And Operation Instructions Manual preview
SmarTemp Control fx
Бренд: Webasto Страницы: 8
ICP DAS USA ALM-04-MRTU User Manual preview
ALM-04-MRTU
Бренд: ICP DAS USA Страницы: 26
National Instruments cRIO-FRC II User Manual And Specifications preview
cRIO-FRC II
Бренд: National Instruments Страницы: 22
J+J J4C 20 Assembly Instructions Manual preview
J4C 20
Бренд: J+J Страницы: 6
Guangdong Schen Investment RC-M2 User Manual preview
RC-M2
Бренд: Guangdong Schen Investment Страницы: 15
AGRI TRONIX DIGI-STAR GT400 Operator'S Manual preview
DIGI-STAR GT400
Бренд: AGRI TRONIX Страницы: 26
B&R Automation PC 620 User Manual preview
Automation PC 620
Бренд: B&R Страницы: 594
Analog Devices ADuCM355 Hardware Reference Manual preview
ADuCM355
Бренд: Analog Devices Страницы: 312
Native Instruments komplete kontrol s series Manual preview
komplete kontrol s series
Бренд: Native Instruments Страницы: 338

Бренды по названию

Популярные бренды

Загрузить еще бренды