manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

RM0082

RS_SDIO controller

Doc ID 018672 Rev 1

727/844

32.7.25 CAP2 

register

The CAP2 bit assignments are given in 

Table 648

.

         

32.7.26 MAXCURR1 

register

The MAXCURR1 bit assignments are given in 

Table 649

.

         

[13:08]

BCLKFREQ

6’h30

Hwinit

This value indicates the base (maximum) clock
frequency for the SD clock. Unit values are 1 MHz.
If the real frequency is 16.5 MHz, the larger value
shall be set 0x11 (17 MHz) because the HD uses
this value to calculate the clock divider value and it
shall not exceed the upper limit of the SD clock
frequency. The supported range is 10 MHz to 63
MHz. If these bits are all 0, the Host System has to
get information via another method. 

Not 0 - 1 MHz to 63 MHz

0x00 - Get information via another method.

[07]

TOCLKU

1’h1

Hwinit

This bit shows the unit of base clock frequency
used to detect Data Timeout Error.

1’b0 - kHz

1’b1 - MHz

[06]

-

-

Rsvd

Reserved

[05:00]

TOCLKFREQ

6’h30

Hwinit

This bit shows the base clock frequency used to
detect Data Timeout Error. 

Not 0 - 1 kHz to 63 kHz or

1 MHz to 63 MHz

0x00- Get Information via another method.

Table 647.

CAP1 register bit assignments (continued)

Bit

Name

Reset 
value

Type

Description

Table 648.

CAP2 register bit assignments

Bit

Name

Reset 
value

Type

Description

[31:00]

-

-

Rsvd

Reserved

Table 649.

MAXCURR1 register bit assignments

Bit

Name

Reset 
value

Type

Description

[31:24]

-

-

Rsvd

Reserved

[23:16]

MAX18CURR 8’h00

Hwinit

Maximum current for 1.8V card. (See 

Table 651

)

[15:08]

MAX30CURR 8’h00

Hwinit

Maximum current for 3.0V card. (See 

Table 651

)

[07:00]

MAX33CURR 8’h01

Hwinit

Maximum current for 3.3V card. (See 

Table 651

)

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

Securi-Prod LK190 Installation Manual preview
LK190
Бренд: Securi-Prod Страницы: 3
Toptech MultiLoad II EXL Installation Manual preview
MultiLoad II EXL
Бренд: Toptech Страницы: 83
Winbond W77E516 Manual preview
W77E516
Бренд: Winbond Страницы: 85
H.E. Anderson Ratio Feeder J+ Advanced Series Manual preview
Ratio Feeder J+ Advanced Series
Бренд: H.E. Anderson Страницы: 11
Vageo RT-1 Manual preview
RT-1
Бренд: Vageo Страницы: 2
DirectConnect VC70DSW Instructions preview
VC70DSW
Бренд: DirectConnect Страницы: 2
AMX NetLinx Integrated Controller NI-3100 Installation Manual preview
NetLinx Integrated Controller NI-3100
Бренд: AMX Страницы: 2
Invacare MK5 NX w/ACC Service Manual preview
MK5 NX w/ACC
Бренд: Invacare Страницы: 44
S&P REB 1 Manual preview
REB 1
Бренд: S&P Страницы: 8
Thermal Solutions Boiler Control TSBC Instruction Manual preview
Boiler Control TSBC
Бренд: Thermal Solutions Страницы: 48
Trio MC206X Quick Connection Manual preview
MC206X
Бренд: Trio Страницы: 8
ELMARK CD-701 Instructions For Installation And Use Manual preview
CD-701
Бренд: ELMARK Страницы: 7
Atkinson Electronics PVLC-40MD Quick Start Manual preview
PVLC-40MD
Бренд: Atkinson Electronics Страницы: 3
pleiger 362MC Manual preview
362MC
Бренд: pleiger Страницы: 59
Wecon LX3V-4AD User Manual preview
LX3V-4AD
Бренд: Wecon Страницы: 12
PICO Solareg PICO 200 Operating Manual preview
Solareg PICO 200
Бренд: PICO Страницы: 12
ATTO Technology FibreBridge 7500 Getting Started Manual preview
FibreBridge 7500
Бренд: ATTO Technology Страницы: 2
Solvis DeltaControl Operation preview
DeltaControl
Бренд: Solvis Страницы: 44

Бренды по названию

Популярные бренды

Загрузить еще бренды