manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

RM0082

RS_SDIO controller

Doc ID 018672 Rev 1

713/844

32.7.15 TMOUTCTRL 

register 

The TMOUTCTRL bit assignments are given in 

Table 634

.

         

Note:

At the initialization of the HC, the HD shall set the Data Time-out Counter Value according to
the Capabilities register.

[01]

INCLKST

1’h0

ROC

This bit is set to logic ‘1’ when SD clock is stable
after writing to Internal Clock Enable in this register
to logic ‘1’. The SD Host Driver shall wait to set SD
Clock Enable until this bit is set to 1.

Note: This is useful when using PLL for a clock
oscillator that requires setup time. 

1’b1 - Ready

1’b0 - Not Ready

[00]

INCLKEN

1’h0

RW

This bit is set to logic ‘0’ when the HD is not using
the HC or the HC awaits a wakeup event.

The HC should stop its internal clock to go very low
power state. Still, registers shall be able to be read
and written. Clock starts to oscillate when this bit is
set to logic ‘1’. When clock

oscillation is stable, the HC shall set Internal Clock
Stable in this register to logic ‘1’. This bit shall not
affect card detection.

1’b1 - Oscillate

1’b0 - Stop

Table 633.

CLKCTRL register bit assignments (continued)

Bit

Name

Reset 
value

Type

Description

Table 634.

TMOUTCTRL register bit assignments

Bit

Name

Reset 
value

Type

Description

[07:04]

-

-

Rsvd

Reserved

[03:00]

DATATMCNT 4’h0

RW

This value determines the interval by which DAT line
time-outs are detected. Refer to the Data Time-out
Error in the Error Interrupt Status register for
information on factors that dictate time-out generation.
Time-out clock frequency will be generated by dividing
the base clock TMCLK by this value. When setting this
register, prevent inadvertent time-out events 

by

clearing the Data Time-out Error Status Enable
(

Table 32.7.20

).

4’b1111 - Reserved

4’b1110 - TMCLK * 2^27

------------------------------

------------------------------

4’b0001 - TMCLK * 2^14

4’b0000 - TMCLK * 2^13

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

Camozzi PRE Series Operation And Maintenance Instructions preview
PRE Series
Бренд: Camozzi Страницы: 33
Camozzi PME Series Operation & Maintenance Instructions Manual preview
PME Series
Бренд: Camozzi Страницы: 64
ZKTeco SRB Connection Manual preview
SRB
Бренд: ZKTeco Страницы: 2
Auber WS-1500FXL Operation & Instruction Manual preview
WS-1500FXL
Бренд: Auber Страницы: 3
Samcen SCS8000E Administrator'S Manual preview
SCS8000E
Бренд: Samcen Страницы: 65
ADLINK Technology PCIe-8332 User Manual preview
PCIe-8332
Бренд: ADLINK Technology Страницы: 37
Watlow Ramping and Profiling Microprocessor-Based Control SERIES 1500 User Manual preview
Ramping and Profiling Microprocessor-Based Control SERIES 1500
Бренд: Watlow Страницы: 90
CAME BIANCA-VC Installation Manual preview
BIANCA-VC
Бренд: CAME Страницы: 32
JLCooper Electronics SloMoPro User Manual preview
SloMoPro
Бренд: JLCooper Electronics Страницы: 11
Danfoss AMD 610 AS Installation Manual preview
AMD 610 AS
Бренд: Danfoss Страницы: 2
mikroElektronika BIGdsPIC6 User Manual preview
BIGdsPIC6
Бренд: mikroElektronika Страницы: 28
TA DA 516 Manual preview
DA 516
Бренд: TA Страницы: 8
Abov MC96F8204 Series User Manual preview
MC96F8204 Series
Бренд: Abov Страницы: 212
Whelen Engineering Company MPC03 Installation & Operating Manual preview
MPC03
Бренд: Whelen Engineering Company Страницы: 10
Sutron XLink 100 Operation & Maintenance Manual preview
XLink 100
Бренд: Sutron Страницы: 201
Arroyo Instruments ComboPak 685 Series User Manual preview
ComboPak 685 Series
Бренд: Arroyo Instruments Страницы: 52
Hoffman Controls 816-10DH Installation & Operating Instructions preview
816-10DH
Бренд: Hoffman Controls Страницы: 4
Saci Pumps emotion MT2-11A Installation And Maintenance Manual preview
emotion MT2-11A
Бренд: Saci Pumps Страницы: 262

Бренды по названию

Популярные бренды

Загрузить еще бренды