manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

RS_SDIO controller

RM0082

716/844

Doc ID 018672 Rev 1

[06]

CDIINT

1’h0

RW1C

This status is set if the Card Inserted in the Present
State register changes from 0 to 1. When the HD
writes this bit to logic ‘1’ to clear this 

status the status of the Card Inserted in the Present
State register should be confirmed. Because the
card detect may possibly be changed when the HD
clear this bit an Interrupt event may not be
generated.

1’b0 - Card State Stable or Debouncing

1’b1 - Card Inserted

[05]

BUFRDRDY

1’h0

RW1C

This status is set if the Buffer Read Enable changes
from 0 to 1.

1’b0 - Not Ready to read Buffer.

1’b1 - Ready to read Buffer.

[04]

BUFWRRDY

1’h0

RW1C

This status is set if the Buffer Write Enable changes
from 0 to 1.

1’b0 - Not Ready to Write Buffer.

1’b1 - Ready to Write Buffer.

[03]

DMAINT

1’h0

RW1C

This status is set if the HC detects the Host DMA
Buffer Boundary in the Block Size register.

1’b0 - No DMA Interrupt

1’b1 - DMA Interrupt is Generated

[02]

BLKGAPE

1’h0

RW1C

If the Stop At Block Gap Request in the Block Gap
Control Register is set, this bit is set.

Read Transaction:

This bit is set at the falling edge of the DAT Line
Active Status (When the transaction is stopped at
SD Bus timing. The Read Wait must be supported
in order to use this function). 

Write Transaction:

This bit is set at the falling edge of Write Transfer
Active Status (After getting CRC status at SD Bus
timing). 

1’b0- No Block Gap Event

1’b1 - Transaction stopped at Block Gap

Table 636.

NIRQSTAT register bit assignments (continued)

Bit

Name

Reset 
value

Type

Description

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

IBM ServeRAID M5014 User Manual preview
ServeRAID M5014
Бренд: IBM Страницы: 106
We Care Solar Suitcase Installation Manual preview
Suitcase
Бренд: We Care Solar Страницы: 46
EBS CPX200NB Installation And Programming Manual preview
CPX200NB
Бренд: EBS Страницы: 116
Daikin BRC1H62W Operation Handbook preview
BRC1H62W
Бренд: Daikin Страницы: 2
Leviton GreenMax DRC DRC07-ED0 Quick Start Manual preview
GreenMax DRC DRC07-ED0
Бренд: Leviton Страницы: 2
TECH EU-391 ZPID User Manual preview
EU-391 ZPID
Бренд: TECH Страницы: 20
Velleman-Kit EDU01 Manual preview
EDU01
Бренд: Velleman-Kit Страницы: 32
KEPCO MST 488-27HT Operator'S Manual preview
MST 488-27HT
Бренд: KEPCO Страницы: 34
Sorel SBMC Installation And Operating Instructions Manual preview
SBMC
Бренд: Sorel Страницы: 20
A-T Controls Triad Controls WE Series Installation And Operation Manual preview
Triad Controls WE Series
Бренд: A-T Controls Страницы: 13
Texas Instruments TDP0604 User Manual preview
TDP0604
Бренд: Texas Instruments Страницы: 19
WAGO 8003 Series Operating And Assembly Instructions preview
8003 Series
Бренд: WAGO Страницы: 2
G-Scale Graphics LSCM2 Operation And Installation Manual preview
LSCM2
Бренд: G-Scale Graphics Страницы: 7
VARIZOOM VZ-ROCK Operating Instructions preview
VZ-ROCK
Бренд: VARIZOOM Страницы: 2
PACH & COMPANY QUANTUM Q5VOIP Manual preview
QUANTUM Q5VOIP
Бренд: PACH & COMPANY Страницы: 39
AMD Am7990 Reference Manual preview
Am7990
Бренд: AMD Страницы: 12
Barco Sedomat 2500 Features & Benefits preview
Sedomat 2500
Бренд: Barco Страницы: 2
Zaber T-CON3 User Manual preview
T-CON3
Бренд: Zaber Страницы: 23

Бренды по названию

Популярные бренды

Загрузить еще бренды