manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

AS_Cryptographic co-processor (C3)

RM0082

404/844

Doc ID 018672 Rev 1

         

Bit 26 - Instruction Decode Error (IERR)

The UHH Channel goes in error state and this bit is set if an invalid instruction is received 
from the Instruction Dispatcher.

         

Bit 25 - Alignment Error (AERR)

The Source Address and the Destination Address must be 32 bit aligned. Count must be a 
multiple of 4 Bytes. The UHH Channel goes in error state and this bit is set if any of these 
condition is not respected.

         

Bits 23 to 17 - Reserved

These bits are reserved and should be written zero.

Bit 16 - Reset Command (RST)

In Hardware the reset is done synchronously and not all registers are affected by it. The 
following are the effects of a synchronous reset: bits 29-24, 16, 7-0 of SCR are all cleared, 
FIFOs are flushed, the UHH Channel goes in Idle state eventually aborting instruction 
execution and bits 31-30 (CS) of UHH_CU_CONTROL_STATUS are set to Idle.

         

Bit 27 BERR

Description

1’b1

The Channel was requested to become a Chaining-master, or 
simultaneously both a Couple-Master and a Slave for cascade 
CCM operations.

1’b0

(Clearing conditions) This flag is cleared in two ways: resetting 
the UHH Channel or requesting an asynchronous master reset.

Bit 26 BERR

Description

1’b1

The UHH Channel received an invalid instruction from the 
Instruction Dispatcher.

1’b0

(Clearing conditions) This flag is cleared in two ways: resetting 
the UHH Channel or requesting an asynchronous master reset.

Bit 25 BERR

Description

1’b1

The UHH Channel received an invalid address or count part.

1’b0

(Clearing conditions) This flag is cleared in two ways: resetting 
the UHH Channel or requesting an asynchronous master reset.

Bit 26 RST

Description

1’b1

Reset the UHH Channel

1’b0

(Clearing conditions) This bit is cleared as a consequence of 
the reset, so it is always read zero. Writing zero has no effect.

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

Oceanic ZX Service Procedure preview
ZX
Бренд: Oceanic Страницы: 13
Jetline 9600 Series Operation Manual preview
9600 Series
Бренд: Jetline Страницы: 58
Yudian AI Series Operation Instruction Manual preview
AI Series
Бренд: Yudian Страницы: 26
Easy Heat RS2 Installation And Operation Instructions preview
RS2
Бренд: Easy Heat Страницы: 4
Salda TPC User Manual preview
TPC
Бренд: Salda Страницы: 16
Vacon 100 HVAC User Manual preview
100 HVAC
Бренд: Vacon Страницы: 50
Phoenix Contact 2297031 Manual preview
2297031
Бренд: Phoenix Contact Страницы: 56
HANYOUNG NUX TPR-3N Instruction Manual preview
TPR-3N
Бренд: HANYOUNG NUX Страницы: 4
ICP DAS USA ISaGRAF WinCE ViewPAC User Manual preview
ISaGRAF WinCE ViewPAC
Бренд: ICP DAS USA Страницы: 192
GIESSE RACK MAX 650 Instruction And Installation Manual preview
RACK MAX 650
Бренд: GIESSE Страницы: 136
Universal Remote Control total control MRX-10 Owner'S Manual preview
total control MRX-10
Бренд: Universal Remote Control Страницы: 16
PTZOptics PT-JOY-G4 Quick Start Manual preview
PT-JOY-G4
Бренд: PTZOptics Страницы: 4
Parker ACR1505 Hardware Installation preview
ACR1505
Бренд: Parker Страницы: 64
Metek TWRF1 SCR Series Instruction, Operation And Maintenance Manual preview
TWRF1 SCR Series
Бренд: Metek Страницы: 36
Tyco DSC WT5500 Installation Instructions Manual preview
DSC WT5500
Бренд: Tyco Страницы: 32
SUPMEA SUP-PH8.0 User Manual preview
SUP-PH8.0
Бренд: SUPMEA Страницы: 32
Maxon 688770 Hardware Reference Manual preview
688770
Бренд: Maxon Страницы: 64
SAES NEG POWER User Manual preview
NEG POWER
Бренд: SAES Страницы: 36

Бренды по названию

Популярные бренды

Загрузить еще бренды