manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

RM0082

LS_Universal asynchronous receiver/transmitter (UART)

Doc ID 018672 Rev 1

593/844

UARTRXINTR

●

This interrupt is asserted when one of the following events occurs:

●

If the FIFOs are enabled and the Receive FIFO reaches the programmed trigger level. 

●

The interrupt is then cleared by reading data from the Receive FIFO until it becomes 
less than the trigger level, or by clearing the interrupt;

●

If the FIFOs are disabled and data is received thereby filling the location. The interrupt 
is then cleared by performing a single read of the Receive FIFO, or by clearing the 
interrupt (writing a 1‘b1 to the corresponding bit of the UARTICR register).

UARTTXINTR

●

This interrupt is asserted when one of the following events occurs:

●

If the FIFOs are enabled (FEN bit set to 1‘b1 in UARTLCR_H register) and the Transmit 
FIFO reaches the programmed trigger level (TXIFLSEL in UARTIFLS register). The 
interrupt is then cleared by writing data to the Transmit FIFO until it becomes greater 
than the trigger level, or by clearing the interrupt (writing a 1‘b1 to the corresponding bit 
of the UARTICR register);

●

If the FIFOs are disabled and there is no data in the transmitter single location. The
interrupt is then cleared by performing a single write to the Transmit FIFO, or by
clearing the interrupt (writing a 1‘b1 to the corresponding bit of the UARTICR register).

UARTRTINTR

●

This interrupt is asserted when the Receive FIFO is not empty, and no further data is 
received over a 32 bit period. The interrupt is then cleared either when the Receive 
FIFO becomes empty through reading all the data (or by reading the holding register), 
or by clearing the interrupt (writing a 1‘b1 to the corresponding bit of the UARTICR 
register).

UARTMSINTR

●

This interrupt feature is available in UART only. It represents the modem status 
interrupt, that is a combined interrupt of the four individual modem status lines 
(

nUARTRI

, 

nUARTCTS

, 

nUARTDCS

 and 

nUARTDSR

). This interrupt is then asserted if 

any of the modem status lines change.

UARTEINTR

●

This error interrupt is triggered when there is an error in the reception of the data. The 
interrupt can be caused by a number of different error conditions, such as overrun, 
break, parity and framing.

UARTINTR

●

It is the OR logical function of all the individual masked interrupt sources. That is, this 
interrupt is asserted if any of the individual interrupts are asserted and enabled.

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

S&C 5800 Series Troubleshooting Manual preview
5800 Series
Бренд: S&C Страницы: 34
Danfoss VLT 2800 Instruction Manual preview
VLT 2800
Бренд: Danfoss Страницы: 7
Zeagle Razor Service Manual preview
Razor
Бренд: Zeagle Страницы: 37
WAC T24-OD-CTR Installation Instruction preview
T24-OD-CTR
Бренд: WAC Страницы: 5
TEL AFA4000/1/AS Installation And Calibration Manual preview
AFA4000/1/AS
Бренд: TEL Страницы: 26
Vimar EAM6 Installation And Operation Manual preview
EAM6
Бренд: Vimar Страницы: 32
bluelab Dosetronic Instruction Manual preview
Dosetronic
Бренд: bluelab Страницы: 39
D+H VCD 203 Manual preview
VCD 203
Бренд: D+H Страницы: 16
CompuPro DISK 3 Technical Manual preview
DISK 3
Бренд: CompuPro Страницы: 33
Black Stone BL 981411-0 Instruction Manual preview
BL 981411-0
Бренд: Black Stone Страницы: 2
GIESSE RACK MAX 650 Instruction And Installation Manual preview
RACK MAX 650
Бренд: GIESSE Страницы: 136
DAPAudio IPS-VC3 User Manual preview
IPS-VC3
Бренд: DAPAudio Страницы: 11
Akytec SMI200 User Manual preview
SMI200
Бренд: Akytec Страницы: 15
Melexis DVK90121 User Manual preview
DVK90121
Бренд: Melexis Страницы: 13
Eclipse TRILOGY T500 Series Instruction Manual preview
TRILOGY T500 Series
Бренд: Eclipse Страницы: 20
Window Master MotorController WCC 310 UL Installation Instructions Manual preview
MotorController WCC 310 UL
Бренд: Window Master Страницы: 39
Bamo BAMOWIZ DOZ User Manual preview
BAMOWIZ DOZ
Бренд: Bamo Страницы: 10
Base Line BaseStation 1000 Quick Start Manual preview
BaseStation 1000
Бренд: Base Line Страницы: 11

Бренды по названию

Популярные бренды

Загрузить еще бренды