manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

RS_Telecom IP

RM0082

794/844

Doc ID 018672 Rev 1

[28]

ABBM

Automatic buffer bank management:

When ABBM = 0

,

 the AHB delivers the full address for the buffer 

memory access. The processor then need to know which bank 
is available for it. When it accesses the wrong bank a bad value 
is returned.

When ABBM = 1

, the MSB of the address will be overwritten by 

the RAS. The AHB will then only access to the part that is 
available for it.

Anyway, care must be taken during a short time when the 
memory is reserved for the RAS. In this case the AHB access if 
any will be corrupted. To avoid this, there should be no AHB 
access while the Nsh (not_shared_memory) bit is "1". NSh will 
generate an interrupt to inform that the memory can be 
accessed.

[27]

BBVal

This bit denotes the buffer bank in case the two buffer banks 
cannot toggle (BBfrz = 1).

[26]

BBfrz

buffer banks frozen

When BBfrz =0

, the two buffer banks can toggle. 

When BBfrz= 1

,

 the two banks are frozen. The used bank is 

given by BBVal.

[25]

nAHB_L

The value to force for the lower buffer memory for the AHB 

nAHB_L = 0:

 the AHB is able to read/write the BUF memory in 

the lower bank.

nAHB_L = 1: 

RAS logic can access the lower BUF memory if 

BB = 0, AHB can access the lower BUF memory if BB = 1.

[24]

nAHB_H

The value to force for the upper buffer memory for the AHB

nAHB_H = 0:

 

the AHB is able to read/write the BUF memory in 

the upper bank.

nAHB_H = 1: 

RAS logic can access the upper BUF memory if 

BB = 1, AHB can access the upper memory if BB = 0.

[23]

S47

Informs if one of the SYNC4 to SYNC7 signals are used 
externally.

S47 = 0: 

no SYNC7-4 signal is used. It is not useful to read the 

SYNC memory.

S47 = 1

:

 

at least one of the SYNC7-4 signals is used.

[22:21]

Bdel3

Delay in byte between the 

SYNC3

 

and one of the previous 

channels.

Bdel3[1]

Bdel3[0]

Delay

0

0

No delay

0

1

1  byte

1

0

2  bytes

1

1

4  bytes

Table 718.

TDM_SYNC_GEN register (Offset 0x40) (continued)

Bits

Name

Comments

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

Jands SafeGuard Installation Manual preview
SafeGuard
Бренд: Jands Страницы: 7
hager coviva Smartbox TKP100A Operation And Configuration Instructions preview
coviva Smartbox TKP100A
Бренд: hager Страницы: 34
Namron ZigBee Quick Start Manual preview
ZigBee
Бренд: Namron Страницы: 3
Parkside PDWE 8 A2 Operation And Safety Notes Translation Of The Original Instructions preview
PDWE 8 A2
Бренд: Parkside Страницы: 65
Samson 3372 User Manual preview
3372
Бренд: Samson Страницы: 8
Zaiput Flow Technologies BPR-1000 Instruction Manual preview
BPR-1000
Бренд: Zaiput Flow Technologies Страницы: 10
SYCLOPE TRACE'O Manual preview
TRACE'O
Бренд: SYCLOPE Страницы: 60
Atari IDEa How To Connect preview
IDEa
Бренд: Atari Страницы: 3
Swagelok BSH 10 Series User Manual preview
BSH 10 Series
Бренд: Swagelok Страницы: 20
Danfoss ADAP-KOOL AK-PC 781 Design Manual preview
ADAP-KOOL AK-PC 781
Бренд: Danfoss Страницы: 142
Kele UCM-420A Operating And Installation Instructions preview
UCM-420A
Бренд: Kele Страницы: 33
salmson EC-Drain 2x4,0 Installation And Starting Instructions preview
EC-Drain 2x4,0
Бренд: salmson Страницы: 37
Harsen GU641A Operation Manual preview
GU641A
Бренд: Harsen Страницы: 55
Wabtec Ricon 55914 Installation Instructions preview
Ricon 55914
Бренд: Wabtec Страницы: 5
X10 SC503 Owner'S Manual preview
SC503
Бренд: X10 Страницы: 3
GAC EEG7000 Manual preview
EEG7000
Бренд: GAC Страницы: 22
Eaton Smart Home Controller 2.0 Quick Installation Manual preview
Smart Home Controller 2.0
Бренд: Eaton Страницы: 24
DYNACO DYNALOGIX II DY 4000 Electrical Manual preview
DYNALOGIX II DY 4000
Бренд: DYNACO Страницы: 13

Бренды по названию

Популярные бренды

Загрузить еще бренды