manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

LS_I2C controller

RM0082

624/844

Doc ID 018672 Rev 1

         

28.6.5 IC_SAR 

register(0x008)

The IC_SAR is the 10 bit RW register which holds the slave address. The I

2

C controller 

responds to this address when it is operating as a slave. In case of 7 bit addressing 
(IC_10BITADDR_SLAVE bit set to ‘b0 in IC_CON register, 

Section 28.6.3

), only bits [6:0] 

are used. The IC_SAR bit assignments are given in 

Table 544

.

Note:

This register can be written only when the I

2

C controller is disabled, which corresponds to 

the IC_ENABLE (

Section 28.6.21

) register being set to ’b0. Write at other times has no 

effect.

Table 543.

IC_TAR register bit assignments

Bit

Name

Type

Reset 
value

Description

[15:13]

Reserved

-

Read: undefined. Write: should be zero.

[12]

IC_10BITADDR_MAST
ER

RW

1’h0

10 bit addressing mode (when acting as 
master).

this bit controls whether DW_apb_i2c starts its 
transfer in 10 bit addressing mode when acting 
as a master according to the encoding below:

1‘b0 = 7.

1‘b1 = 10.

[11]

SPECIAL

RW

1’h0

Perform a general call or start byte I

2

C 

command.

This bit indicates whether software would like 
to either perform a general call or start byte I

2

C 

command, according to the encoding:

1‘b0 = Ignore bit[10], GC_OR_START, in this 
register and use IC_TAR normally.

1‘b1 = Perform special I

2

C command as 

specified in GC_OR_START bit.

[10]

GC_OR_START

RW

1’h0

Indicates when a general call or start byte I

2

C 

command is to be performed.

If bit[11], SPECIAL, in this register is set to ‘b1, 
the GC_OR_START bit indicates whether a 
general call or start byte command is to be 
performed by the I

2

C controller, according to 

the encoding below:

1‘b0 = General Call Address: after issuing a 
general call, only writes may be performed. 
Attempting to issue a read command result in 
setting TX_ABRT. The I

2

C controller remains in 

general call mode until the SPECIAL bit value 
is cleared.

1‘b1 = Start byte.

[09:00]

IC_TAR

RW

10’h0
55

Target address.

This 10 bit field is the target address for any 
master transactions. Its reset value indicates 
loopback mode.

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

NCR 1651 Quick Reference Manual preview
1651
Бренд: NCR Страницы: 6
Walchem W100 Troubleshooting Manual preview
W100
Бренд: Walchem Страницы: 10
Lawler 804 Installation & Maintenance Manual preview
804
Бренд: Lawler Страницы: 5
nekos SKY 650 Manual For Installation And User Manual preview
SKY 650
Бренд: nekos Страницы: 8
nekos SKY 450 Installation And Use Manual preview
SKY 450
Бренд: nekos Страницы: 8
S&P RMB Quick Start Manual preview
RMB
Бренд: S&P Страницы: 17
Allen-Bradley CENTERLINE Instruction Manual preview
CENTERLINE
Бренд: Allen-Bradley Страницы: 88
Danfoss AVT/VG Operating Manual preview
AVT/VG
Бренд: Danfoss Страницы: 16
LOVATO ELECTRIC DCRJ Addendum preview
DCRJ
Бренд: LOVATO ELECTRIC Страницы: 18
S&P CONTROL ECOWATT Manual preview
CONTROL ECOWATT
Бренд: S&P Страницы: 32
Dataprobe iPIO-16 Quick Start Manual preview
iPIO-16
Бренд: Dataprobe Страницы: 2
V2 AYROS 1000D 24V-120V Manual preview
AYROS 1000D 24V-120V
Бренд: V2 Страницы: 116
FCS FWC-1101 Installation Manual preview
FWC-1101
Бренд: FCS Страницы: 6
Scaime eNod4-C BOX Manual preview
eNod4-C BOX
Бренд: Scaime Страницы: 74
Carel KITCONT101SP Assembly preview
KITCONT101SP
Бренд: Carel Страницы: 2
Texas Instruments Concerto F28M36 Series Technical Reference Manual preview
Concerto F28M36 Series
Бренд: Texas Instruments Страницы: 1692
Verdin DBC 870 User Manual preview
DBC 870
Бренд: Verdin Страницы: 37
Eaton SVCH0203 SPX Advanced Applications Manual preview
SVCH0203 SPX Advanced
Бренд: Eaton Страницы: 185

Бренды по названию

Популярные бренды

Загрузить еще бренды