manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

RM0082

BS_DMA controller

Doc ID 018672 Rev 1

341/844

         

19.7.6 DMACIntErrorStatus 

register

The DMACIntErrorStatus (interrupt error status) is a RO register which shows the status of 
the error request after masking. The DMACIntErrorStatus bit assignments are given in 

Table 285

.

Note:

This register must be used in conjunction with the DMACIntStatus register if the combined 
interrupt request, DMACINTR, is used. If the DMACINTERR interrupt request is used, 
reading this register only is enough to determine source of the interrupt request.

         

19.7.7 DMACIntErrClr 

register

The DMACIntErrClr (interrupt error clear) is a WO register which allow to clear an error 
interrupt request. The DMACIntErrClr bit assignments are given in 

Table 286

.

         

Table 284.

DMACIntTCClear register bit assignments

Bit

Name

Reset value Description

[31:08]

Reserved

-

Write as zero.

[07:00]

IntTCClear

8’h00

Terminal count request clear.

Each bit is associated to a DMA channel. When writing to 
this register, each bit that is set causes the corresponding bit 
in the DMACIntTCStatus register to be cleared. In contrast, 
bits that are not set have no effect on the corresponding bit 
in the DMACIntTCStatus register.

Table 285.

DMA ClntErrorStatus register bit assignments

Bit

Name

Reset 
Value

Description

[31:08]

Reserved

-

Read: undefined.

[07:00]

IntErrorStatus

8’h00

Interrupt error status.

Each bit is associated to a DMA channel. If a bit is set, it 
means that an interrupt error request is active for the 
relevant DMA channel.

Table 286.

DMACIntErrClr register bit assignments

Bit

Name

Reset value

Description

[31:08]

Reserved

-

Write as zero.

[07:00]

IntErrClr

8’h00

Interrupt error request clear.

Each bit is associated to a DMA channel. When writing to 
this register, each bit that is set causes the corresponding bit 
in the DMACIntErrorStatus register to be cleared. In 
contrast, bits that are not set have no effect on the 
corresponding bit in the DMACIntErrorStatus register.

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

IBM 3708 End-User Reference preview
3708
Бренд: IBM Страницы: 144
Hable One Starting Manual preview
One
Бренд: Hable Страницы: 3
Talgil DREAM 2 Manual preview
DREAM 2
Бренд: Talgil Страницы: 14
Eaton EZD Series User Manual preview
EZD Series
Бренд: Eaton Страницы: 448
Frico ERP Instruction Manual preview
ERP
Бренд: Frico Страницы: 12
Acuity Controls nLight ECLYPSE Safety Instructions preview
nLight ECLYPSE
Бренд: Acuity Controls Страницы: 5
Bard CompleteStat-Series CS9B-THO Product Manual preview
CompleteStat-Series CS9B-THO
Бренд: Bard Страницы: 2
Beckhoff CX8080 Documentation preview
CX8080
Бренд: Beckhoff Страницы: 67
Omron K8AK-LS Manual preview
K8AK-LS
Бренд: Omron Страницы: 12
Window Master MotorController WCC 310 Installation Instructions Manual preview
MotorController WCC 310
Бренд: Window Master Страницы: 19
JBSYSTEMS Light LS-RGB-DMX CONTROL Manual preview
LS-RGB-DMX CONTROL
Бренд: JBSYSTEMS Light Страницы: 12
CDVI Ievo User Manual preview
Ievo
Бренд: CDVI Страницы: 24
Sices GC315 User And Installation Manual preview
GC315
Бренд: Sices Страницы: 8
Samson 3375 Mounting And Operating Instructions preview
3375
Бренд: Samson Страницы: 130
Powrmatic Eurotrol 2 Installation & User'S Instructions preview
Eurotrol 2
Бренд: Powrmatic Страницы: 10
Watlow Anafaze PPC-2000 User Manual preview
Anafaze PPC-2000
Бренд: Watlow Страницы: 320
dunkermotoren ServoTube 25 Instruction Manual preview
ServoTube 25
Бренд: dunkermotoren Страницы: 34
Texas Instruments TMS320F2837 D Series Errata Sheet preview
TMS320F2837 D Series
Бренд: Texas Instruments Страницы: 48

Бренды по названию

Популярные бренды

Загрузить еще бренды