manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

RS_Flexible static memory controller (FSMC)

RM0082

668/844

Doc ID 018672 Rev 1

[12]

If_we

1'h1

Interface write enable. This bit allows to enable write in NOR 
Flash and SRAM, according to the encoding below:

0 - Disabled.

1 - Enabled (default).

[11]

Wait_delay

1'b0

Wait timing. This bit manages the wait signal from NOR Flash, 
according to the encoding below:

0 - Wait is anticipated.

1 - Wait has the same data timing (delayed). 

[10]

-

-

Reserved. Read: undefined. Write: should be zero.

[09]

WaitPolarity 1'h0

Polarity of wait signal. This bit specifies the polarity of the wait 
signal, according to encoding below:

0 - Active low (default).

1 - Active high

[08]

-

-

Reserved. Read: undefined. Write: should be zero.

[07]

Wprot

1'h1

Write protect signal to Flash memory. This field is applicable only 
to Flash memories. It directly represents the Wprot signal to the 
input pin of the Flash memory, according to the encoding below:

0 - Disabled.

1 - Enabled (default).

Note: Wprot port is not available in 

SPEAr300

.

[06]

RstPwr-
Down

1'h1

Reset/power down signal to Flash memory. This field is applicable 
only to Flash memories. It directly represents the RstPwdwn 
signal to the input pin of the Flash memory. 

Note: Wprot port is not available in 

SPEAr300

.

[05:04]

DevWidth

-

Device width. This 2-bit field is applicable to all types of 
memories, and it indicates the memory data size, according to the 
encoding below:

– 00 - 8 bit

– 01 - 16 bit

– 10 - 32 bit (not used in 

SPEAr300

)

– 11 - Not used.

Default Value is set using bit 30 of the RAS configuration register. 
Register_2, according to the encoding: 0-00 & 1-01

[03:02]

MemType

-

Memory type. This 2bit-field indicates the memory type, according 
to the encoding below:

– 00 - SRAM

– 01  -  Reserved

– 10 - NOR Flash.

– 11  -  Reserved

Bank 0 has ‘b10 as default value, whereas all other banks have 
‘b00

Table 597.

GenMemCtrl(i) register bit assignments (continued)

Bit

Name

Reset 
value

Description

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

Harmonic Drive CHA Engineering Data preview
CHA
Бренд: Harmonic Drive Страницы: 85
Lattice LatticeMico8 User Manual preview
LatticeMico8
Бренд: Lattice Страницы: 23
Zander Aachen SCB Series Operating Instructions Manual preview
SCB Series
Бренд: Zander Aachen Страницы: 44
Zamel Extra Free ROB-01/12-24V Manual Instruction preview
Extra Free ROB-01/12-24V
Бренд: Zamel Страницы: 2
Epsolar eTracer ET4415BND Operation Manual preview
eTracer ET4415BND
Бренд: Epsolar Страницы: 44
ASROCK iEP-5000G Series Quick Installation Manual preview
iEP-5000G Series
Бренд: ASROCK Страницы: 2
Carel EVD mini User Manual preview
EVD mini
Бренд: Carel Страницы: 36
Sulion Driver VISIO IoT Manual preview
Driver VISIO IoT
Бренд: Sulion Страницы: 8
Sentiotec K2-NEXT Installation And Operating Instructions Manual preview
K2-NEXT
Бренд: Sentiotec Страницы: 92
AMALGAMATED INSTRUMENT PM4-RT8 Operation And Instruction Manual preview
PM4-RT8
Бренд: AMALGAMATED INSTRUMENT Страницы: 27
meibes SOL-BASIS Commissioning Manual preview
SOL-BASIS
Бренд: meibes Страницы: 20
Telit Wireless Solutions EVK Series User Manual preview
EVK Series
Бренд: Telit Wireless Solutions Страницы: 49
M-Audio Keyboard Controller Series Quick Start Manual preview
Keyboard Controller Series
Бренд: M-Audio Страницы: 2
ZKTeco Notus Quick Start Manual preview
Notus
Бренд: ZKTeco Страницы: 13
C-LOGIC 502-PC Instruction Manual preview
502-PC
Бренд: C-LOGIC Страницы: 2
Lennox M0STAT61Q-1 Installation & Operation Instructions preview
M0STAT61Q-1
Бренд: Lennox Страницы: 12
Cooper & Hunter LH-13001 Manual preview
LH-13001
Бренд: Cooper & Hunter Страницы: 6
hotset hotcontrol C248 Operating Instructions Manual preview
hotcontrol C248
Бренд: hotset Страницы: 48

Бренды по названию

Популярные бренды

Загрузить еще бренды