manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

RM0082

AS_Cryptographic co-processor (C3)

Doc ID 018672 Rev 1

357/844

21 

AS_Cryptographic co-processor (C3)

21.1 Overview

Within its Application Connection Subsystem, SPEAr300 provides one Channel Control Co-
processor (C3). C3 is a high-performance instruction driven DMA based co-processor. It 
executes instruction flows generated by the host processor. After it has been set-up by the 
host it runs in a completely autonomous way (DMA data in, data processing, DMA data out), 
until the completion of all the requested operations.

C3 has been used to accelerate the processing of cryptographic, security and network 
security applications. It can be used for other types of data intensive applications as well.

Main features provided by the C3 are listed below:

●

C3 Hardware ID base address 0xFFFF_1000.

●

High performance DMA based co-processor enabling the acceleration of data-driven 
computationally expensive functions, such as: Cryptography, Pattern matching, Signal 
Processing, etc.

●

Highly programmable (instruction driven) controller 

●

AMBA AHB 2.0 Master and Slave Interfaces 

●

Scatter and Gather DMA engine 

●

C3 has 8 slots for including channels (hardware accelerators). The configuration is as 
follows:

Channel 0 - Empty

Channel 1 - Data Encryption Standard (DES and TripleDES)

–

DES (56 bit keys, no parity)

–

DES ECB encr decryption

–

DES CBC encr decryption

–

TripleDES (168 bit keys EncDecEnc)

–

3DES ECB encr decryption

–

3DES CBC encr decryption

–

FIFO Size

–

Input FIFO: 16x32 bits

–

Output FIFO: 16x32 bits

Channel 2 - Advanced Encryption Standard (AES)

Channel ID: 0x0000_3000

Supported Algorithms

–

AES (128, 192, 256 bit keys)

–

AES ECB encr decryption

–

AES CBS encr decryption“AES Counter Mode encr decryption

FIFO Size

–

Input FIFO: 16x32 bits

–

Output FIFO: 16x32 bits

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

ABB RHD8000 Series Instructions Manual preview
RHD8000 Series
Бренд: ABB Страницы: 17
TWR Lighting E-1DB2 Manual preview
E-1DB2
Бренд: TWR Lighting Страницы: 49
AirCycler SmartExhaust Manual preview
SmartExhaust
Бренд: AirCycler Страницы: 2
TS Performance Torque Converter Lock-Up Manual preview
Torque Converter Lock-Up
Бренд: TS Performance Страницы: 4
vanEE VENMAR ADVANCED TOUCHSCREEN CONTROL Installation And User Manual preview
VENMAR ADVANCED TOUCHSCREEN CONTROL
Бренд: vanEE Страницы: 4
GOAL ZERO 10 AMP User Manual preview
10 AMP
Бренд: GOAL ZERO Страницы: 52
Infineon XE166 Series Hardware Manual preview
XE166 Series
Бренд: Infineon Страницы: 28
ZiLOG Z8 Encore! XP Dual F1680 Series User Manual preview
Z8 Encore! XP Dual F1680 Series
Бренд: ZiLOG Страницы: 18
Danfoss AME 56K Instructions Manual preview
AME 56K
Бренд: Danfoss Страницы: 10
Powtran PR5200 Series Manual preview
PR5200 Series
Бренд: Powtran Страницы: 36
wattstopper LMRC-111 Quick Start Manual preview
LMRC-111
Бренд: wattstopper Страницы: 4
Zamel RTS-01A Instruction Manual preview
RTS-01A
Бренд: Zamel Страницы: 2
ICStation EQKIT Manual preview
EQKIT
Бренд: ICStation Страницы: 3
NELSEN WATER NRO ROC2 Documentation preview
NRO ROC2
Бренд: NELSEN WATER Страницы: 16
Samson 3375 Mounting And Operating Instructions preview
3375
Бренд: Samson Страницы: 130
Sunlight Supply TITAN Controls Saturn 4 Instruction Manual preview
TITAN Controls Saturn 4
Бренд: Sunlight Supply Страницы: 4
VistaLab 2100-0003 Operating Manual preview
2100-0003
Бренд: VistaLab Страницы: 20
Madas RG/2MT X Series Technical Manual preview
RG/2MT X Series
Бренд: Madas Страницы: 28

Бренды по названию

Популярные бренды

Загрузить еще бренды