manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

RM0082

RS_SDIO controller

Doc ID 018672 Rev 1

731/844

         

32.7.31 ADMAADDR1 

register

The ADMAADDR1 bit assignments are given in 

Table 656

.

32.7.32 ADMAADDR2 

register

The ADMAADDR2 bit assignments are given in 

Table 656

.

[02]

ADMALMER

1’h0

RW

ADMA Length Mismatch Error

This error occurs in the following 2 cases.

While Block Count Enable being set, the total data
length specified by the Descriptor table is different
from that specified by the Block Count and Block
Length. 

Total data length can not be divided by the block
length.

1’b1 - Error

1’b0 - No error

[01:00]

ADMAERST
S

2’h0

RW

ADMA Error State

This field indicates the state of ADMA when error is
occurred during ADMA data transfer. This field
never indicates “10” because ADMA never stops in
this state.

Table 655

 define these bits.

Table 655.

ADMAERRSTS bits[1:0] definition

Bits[1:0]

ADMA Error State when error has 
occurred

Contents of SYS_SDR register

00

ST_STOP (Stop DMA)

Points next of the error descriptor

01

ST_FDS (Fetch Descriptor)

Points the error descriptor

10

Never set this state

(Not used)

11

ST_TFR (Transfer Data)

Points the next of the error descriptor

Table 654.

ADMAERRSTS register bit assignments (continued)

Bit

Name

Reset 
value

Type

Description

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

Zolix Instruments SC300 Operation Manual preview
SC300
Бренд: Zolix Instruments Страницы: 22
Barco Argus Information preview
Argus
Бренд: Barco Страницы: 6
YASKAWA PROFINET V1000 Technical Manual preview
PROFINET V1000
Бренд: YASKAWA Страницы: 49
M-system MSP10 Instruction Manual preview
MSP10
Бренд: M-system Страницы: 17
Frico ERP Instruction Manual preview
ERP
Бренд: Frico Страницы: 12
RADEMACHER Troll Comfort Instruction Manual For The Electrical Connection And For Commissioning preview
Troll Comfort
Бренд: RADEMACHER Страницы: 112
Newport i/8 Quick Start preview
i/8
Бренд: Newport Страницы: 2
Dahua Technology DH-PFM888S-AC User Manual preview
DH-PFM888S-AC
Бренд: Dahua Technology Страницы: 75
ETI PFC 12 RS User And Service Manual preview
PFC 12 RS
Бренд: ETI Страницы: 14
WAGO 750-8202/040-000 Manual preview
750-8202/040-000
Бренд: WAGO Страницы: 418
Linear Technology LTC4232 Demo Manual preview
LTC4232
Бренд: Linear Technology Страницы: 6
BFT COMPASS SC-RS 232 Installation And User Manual preview
COMPASS SC-RS 232
Бренд: BFT Страницы: 24
National Instruments cRIO-9037 Getting Started Manual preview
cRIO-9037
Бренд: National Instruments Страницы: 20
G-Scale Graphics LSCM2 Operation And Installation Manual preview
LSCM2
Бренд: G-Scale Graphics Страницы: 7
hager RTQ520X Manual preview
RTQ520X
Бренд: hager Страницы: 10
AirPatrol Lite combi control Quick Start Manual preview
combi control
Бренд: AirPatrol Lite Страницы: 4
Scratch Live DENON DN-HC4500 Quick Start Manual preview
DENON DN-HC4500
Бренд: Scratch Live Страницы: 13
Parker PAC120 Series Operation Manual preview
PAC120 Series
Бренд: Parker Страницы: 31

Бренды по названию

Популярные бренды

Загрузить еще бренды