manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

RM0082

RS_Telecom IP

Doc ID 018672 Rev 1

767/844

The various sub blocks of Telecom IP are describes in the following sections:-

34.4.1 

Regs and regs_rw blocks

These blocks contain the set of telecom programming registers which are described in detail
in the Programmer’s Model 

Section 34.5

34.4.2 TDM 

clock 

block

The TDM clock block generates the clock in Master mode and recovers the clock in slave
mode. This clock internally is named int_CLK and is used by all the blocks relative to TDM.

The block diagram of this cell is presented here below.

Figure 83.

TDM clock cell block diagram

Externally the TDM clock block is connected to the four customization clock pins (PL_CLK1,
PL_CLK2, PL_CLK3 & PL_CLK4) of the device plus the CLK pin (PL_GPIO35) that is used
in slave mode.

●

PL_CLK1 outputs a clock generated either from pll2 or ClkR_synt(3) {frequency 
synthesizer output 3}. 

●

PL_CLK2 outputs the internal int_CLK signal

●

PL_CLK3 outputs either the inverted int_CLK signal, or the clock source selected by 
the block. This feature allows delivering a clock to an external master device.

●

PL_CLK4 is an input targeted to receive a clock from an oscillator. 

DIV 15-0

DIV_CPT

(16bit)

ACT

M/S

bypass

‘0’

ClkR_Synt(3)

PL_CLK4

CLKSM

Isrc2-0

CLKSM

inv

tck2

Int_CLK

‘0’

‘0’

CLKo1-0

Int_CLK

Internal_clock

CLKo1-0

‘0’

CLR_Pll2

ClkR_Synt(3)

MIIC1-0

PL_CLK1

PL_CLK3

PL_CLK2

PL_GPIO

35

ClkR_osc1

PL_CLK4

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

Hafele DT 100 Operating Instructions Manual preview
DT 100
Бренд: Hafele Страницы: 82
Lattice Semiconductor HDR-60 User Manual preview
HDR-60
Бренд: Lattice Semiconductor Страницы: 26
Koer C35CBMS Manual preview
C35CBMS
Бренд: Koer Страницы: 6
National Instruments PXI-8150B User Manual preview
PXI-8150B
Бренд: National Instruments Страницы: 78
Stramatel SC24 AUTONOM Operating Instructions Manual preview
SC24 AUTONOM
Бренд: Stramatel Страницы: 10
OCL DLC-1.1 Quick Start Manual preview
DLC-1.1
Бренд: OCL Страницы: 2
V2 WES-ADI Instruction Manual preview
WES-ADI
Бренд: V2 Страницы: 60
ENGGA EVC800i Installation & Adjustment Manual preview
EVC800i
Бренд: ENGGA Страницы: 8
Dieffematic LINEA c400 Instructions And Recommendations For The Installer preview
LINEA c400
Бренд: Dieffematic Страницы: 9
Bardac PLX Product Manual preview
PLX
Бренд: Bardac Страницы: 235
S2Tech 699PLUS Instruction Manual preview
699PLUS
Бренд: S2Tech Страницы: 4
POLA HD38 Handbook preview
HD38
Бренд: POLA Страницы: 7
Zmotion ZMC306X Manual preview
ZMC306X
Бренд: Zmotion Страницы: 59
RIFT Actuators RIFT 400 Installation, Operation & Maintenance Instructions Manual preview
RIFT 400
Бренд: RIFT Actuators Страницы: 23
Troy-Bilt TE31 Series User Manual preview
TE31 Series
Бренд: Troy-Bilt Страницы: 11
Magnetek IMPULSE G Plus Series 4 Installation Manual preview
IMPULSE G Plus Series 4
Бренд: Magnetek Страницы: 60
IBM ServeRAID M1015 SAS/SATA Quick Install Manual preview
ServeRAID M1015 SAS/SATA
Бренд: IBM Страницы: 4
dixell XR30CX Installation And Operating Instructions preview
XR30CX
Бренд: dixell Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды