manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

RS_SDIO controller

RM0082

702/844

Doc ID 018672 Rev 1

         

32.7.7 RESP(i) 

registers

The RESP bit assignments are given in 

Table 625

.

[04]

IDXCkEn

1’h0

RW

If this bit is set to 1, the HC shall check the index
field in the response to see if it has the same value
as the command index. If it is not, it is reported as a
Command Index Error. If this bit is set to 0, the
Index field is not checked.

1’b0 - Disable

1’b1 - Enable

[03]

CRCCkEn

1’h0

RW

If this bit is set to 1, the HC shall check the CRC
field in the response. If an error is detected, it is
reported as a Command CRC Error. If this bit is set
to 0, the CRC field is not checked.

1’b0 - Disable

1’b1 - Enable

[02]

-

-

Rsvd

Reserved

[01:00]

RESTypeSel

2’h0

RW

Response Type Select

2’b00 - No Response

2’b01 - Response length 136

2’b10 - Response length 48

2’b11 - Response length 48 check Busy after
response

Table 624.

Relation between parameters and the name of response type

RESTypeSel

IDXCkEn

CRCCkEn

Name of response type

00

0

0

No Response

01

0

1

R2

10

0

0

R3, R4

10

1

1

R1, R6, R5, R7

11

1

1

R1b, R5b

Table 623.

CMD register bit assignments (continued)

Bit

Name

Reset 
value

Type

Description

         

Table 625.

RESP register bit assignments

Bit

Name

Reset 
value

Type

Description

[127:00]

RESP

128’h0

ROC

 

Table 626

 describes the mapping of command 

responses from the SD Bus to this register for each 
response type. In the table, R[ ] refers to a bit range 
within the response data as transmitted on the SD 
Bus, RESP[ ] refers to a bit range within the 
Response register.

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

LANGER EMV-Technik E 1 User Manual preview
E 1
Бренд: LANGER EMV-Technik Страницы: 48
B&G ZEUS S Detailed App Manual preview
ZEUS S
Бренд: B&G Страницы: 19
CalAmp LMU 2630MB Installation Manual preview
LMU 2630MB
Бренд: CalAmp Страницы: 13
Danfoss AFD 2 VFG 2 Operating Manual preview
AFD 2 VFG 2
Бренд: Danfoss Страницы: 8
Acuity Controls nLight ECLYPSE Safety Instructions preview
nLight ECLYPSE
Бренд: Acuity Controls Страницы: 5
Bard CompleteStat-Series CS9B-THO Product Manual preview
CompleteStat-Series CS9B-THO
Бренд: Bard Страницы: 2
Gecko MC-MP Service Manual preview
MC-MP
Бренд: Gecko Страницы: 82
IFM EC2121 System Manual preview
EC2121
Бренд: IFM Страницы: 41
MOBA MOBA-Matic MMC-1000 User Manual preview
MOBA-Matic MMC-1000
Бренд: MOBA Страницы: 172
aerl CoolMax SRX Installation And Operation User Manual preview
CoolMax SRX
Бренд: aerl Страницы: 27
LS Industrial Systems GLOFA G7M-DR20U User Manual preview
GLOFA G7M-DR20U
Бренд: LS Industrial Systems Страницы: 367
A.O. Smith INTELLI-VENT Troubleshooting Manual preview
INTELLI-VENT
Бренд: A.O. Smith Страницы: 46
Phocos CIS05-2L User Manual preview
CIS05-2L
Бренд: Phocos Страницы: 2
Fright Ideas EscapeKeeper JR Quick Start Manual preview
EscapeKeeper JR
Бренд: Fright Ideas Страницы: 2
Watts Industries MS12832 Installation And User Manual preview
MS12832
Бренд: Watts Industries Страницы: 76
Air Torque AT1001U Maintenance Manual preview
AT1001U
Бренд: Air Torque Страницы: 11
FlowLine Switch Pak A*13 series Owner'S Manual preview
Switch Pak A*13 series
Бренд: FlowLine Страницы: 6
BioSmart PV-WM-MFR Operation Manual preview
PV-WM-MFR
Бренд: BioSmart Страницы: 24

Бренды по названию

Популярные бренды

Загрузить еще бренды