manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

LS_I2C controller

RM0082

630/844

Doc ID 018672 Rev 1

Note:

1

This register can be written only when the I

2

C controller is disabled, which corresponds to 

the IC_ENABLE (

Section 28.6.21

) register being set to ‘b0. Write at other times has no 

effect.

2

This register must be set before any I

2

C bus transaction can take place in order to ensure 

proper I/O timing.

It is not necessary to configure this register if the I2C Controller is enabled as slave.

         

         

28.6.13 IC_HS_SCL_LCNT 

register(0x028)

The IC_HS_SCL_LCNT is a 16 bit RW register which allows to set the low period of the SCL 
clock for high-speed mode. The IC_HS_SCL_LCNT bit assignments are given in 

Table 557

.

Note:

1

This register can be written only when the I

2

C controller is disabled, which corresponds to 

the IC_ENABLE (

Section 28.6.21

) register being set to ‘b0. Write at other times has no 

effect.

2

This register must be set before any I

2

C bus transaction can take place in order to ensure 

proper I/O timing.

Table 555. IC_HS_SCL_HCNT register bit assignments

Bit

Name

Type

Reset 
value

Description

[15:00]

IC_HS_SCL_HCNT

RW

16'h0
00a

SCL clock high period count for high speed.

This 16 bit field states the SCL clock high 
period count for high speed. The minimum 
valid value is 6, and hardware prevents that a 
value less than this minimum will be written 
(setting 6 if attempted). 

Table 556. IC_HS_SCL_HCNT sample calculations

I

2

C data rate - 

HS (Kbps)

SCL clock 
frequency
(MHz)

SCL high time 
required min
(µs)

I

2

C bus 

loading
(pF)

IC_HS_SCL_HCNT 
(hex/decimal)

SCL high time 
actual
(µs)

3400

100

60

100

16‘h0006/’d6

60

3400

125

60

100

16‘h0008/’d8

64

3400

1000

60

100

16‘h003C/’d60

60

3400

100

120

400

16‘h000C/’d12

120

3400

125

120

400

16‘h000F/’d15

120

3400

1000

120

400

16‘h0078/’d120

120

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

Panasonic FP7 Series Additional Functions Manual preview
FP7 Series
Бренд: Panasonic Страницы: 45
PSC Solar YQPV-HP360V/100A Installation And Operating Instructions Manual preview
YQPV-HP360V/100A
Бренд: PSC Solar Страницы: 22
Kärcher SensoTimer ST6 Duo eco!ogic Manual preview
SensoTimer ST6 Duo eco!ogic
Бренд: Kärcher Страницы: 96
Danfoss VLTAutomationDrive FC 360 Quick Manual preview
VLTAutomationDrive FC 360
Бренд: Danfoss Страницы: 52
Burkert 8745 MFC Ethernet Operating Instructions Manual preview
8745 MFC Ethernet
Бренд: Burkert Страницы: 70
Instrutech VGC301 User Manual preview
VGC301
Бренд: Instrutech Страницы: 42
V2 WES-ADI Instruction Manual preview
WES-ADI
Бренд: V2 Страницы: 60
ENGGA EVC800i Installation & Adjustment Manual preview
EVC800i
Бренд: ENGGA Страницы: 8
Teradek CTRL.1 Quick Start Manual preview
CTRL.1
Бренд: Teradek Страницы: 10
Yardian PRO19 Series User Manual preview
PRO19 Series
Бренд: Yardian Страницы: 52
M-Audio Keyboard Controller Series Quick Start Manual preview
Keyboard Controller Series
Бренд: M-Audio Страницы: 2
Zonet ZUH2215V Quick Installation Manual preview
ZUH2215V
Бренд: Zonet Страницы: 2
Intrinsyc Open-X 8M User Manual preview
Open-X 8M
Бренд: Intrinsyc Страницы: 38
Omron E53-C4DR4 User Manual preview
E53-C4DR4
Бренд: Omron Страницы: 157
Kaysun KC-FCD2-M Installation & Owner'S Manual preview
KC-FCD2-M
Бренд: Kaysun Страницы: 24
FPTech Auto VH1 User Manual preview
Auto VH1
Бренд: FPTech Страницы: 11
Link4 iPonic 624 Installation And User Manual preview
iPonic 624
Бренд: Link4 Страницы: 70
Danfoss AME 85 QM Operating Manual preview
AME 85 QM
Бренд: Danfoss Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды