manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

RM0082

AS_Cryptographic co-processor (C3)

Doc ID 018672 Rev 1

365/844

the ones in the Instruction Dispatcher Status and Control Register (ID_SCR) of each ID. 
These bits allow knowing the status of all Instruction Dispatcher with a single AHB slave 
read. See the Instruction Dispatcher document section for more details

Bit 23 to 20 - Instruction dispatcher n interrupt status (ISDn)

Interrupt States (IS) of every Instruction Dispatcher are made available in these bits. These 
bits are the same than the ones in the Instruction Dispatcher Status and Control Register 
(ID_SCR) of each ID. Interrupts can be acknowledged using the Status and Control Register 
of the Instruction Dispatcher (ID_SCR) or using these bits. See the Instruction Dispatcher 
document section for more details.

         

Bit 19 - Interrupt status of all instruction dispatchers (ISA)

The Interrupt Status of All Instruction Dispatchers (ISA) is the logical OR of bits ISD3-ISDO. 
This bit represents the state of the Interrupt pin of the C3 document. Writing one to this flag 
has the same effect as writing one in all ISD3-ISDO.

         

Bit 18 - Clear interrupt status on read (CISR)

If the Clear Interrupt Status on Read bit (CISR) is set, clearing of Interrupt States is 
performed by reading the Status and Control Register of the System (SYS_SCR). The 
Status and Control Register of Instruction Dispatchers (ID_SCR) is not affected by this bit.

         

Bit 17 - Big endian (BEND)

Not implemented. This bit should be set to zero.

Bit 23-20 ISDn

Description

1’b1

The Instruction Dispatcher n is requesting an Interrupt.

1’b0

(Clearing conditions) The Interrupt Status (IS) of Instruction 
Dispatcher n can be cleared writing one to this flag. Writing zero 
has no effect.

Bit 19 ISA

Description

1’b1

At least one Instruction Dispatcher is requesting an Interrupt.

1’b0

(Clearing conditions) The Interrupt Status (IS) of Instruction 
Dispatcher can be cleared writing one to this flag. Writing zero 
has no effect.

Bit 18 CISR

Description

1’b1

Reading SYS_SCR dears Interrupt States of all Instruction 
Dispatchers.

1’b0

Do not clear Interrupt States on SYS_SCR read.

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

IBM ServeRAID M5014 User Manual preview
ServeRAID M5014
Бренд: IBM Страницы: 106
Acclaim Lighting Canvas User Manual preview
Canvas
Бренд: Acclaim Lighting Страницы: 32
Sentiotec CV 4 Installation And Operating Instructions Manual preview
CV 4
Бренд: Sentiotec Страницы: 45
EBS CPX200NB Installation And Programming Manual preview
CPX200NB
Бренд: EBS Страницы: 116
Daikin BRC1H62W Operation Handbook preview
BRC1H62W
Бренд: Daikin Страницы: 2
Leviton GreenMax DRC DRC07-ED0 Quick Start Manual preview
GreenMax DRC DRC07-ED0
Бренд: Leviton Страницы: 2
Planar Dome Md4/PCI Installation Manual preview
Dome Md4/PCI
Бренд: Planar Страницы: 162
THK TJU Instruction Manual preview
TJU
Бренд: THK Страницы: 134
UCS SYNCHRO QUASAR AC User Manual preview
SYNCHRO QUASAR AC
Бренд: UCS Страницы: 10
Curtis MultiMode 1214-8 Manual preview
MultiMode 1214-8
Бренд: Curtis Страницы: 41
R-Tec controlR Installation Manual & User Manual preview
controlR
Бренд: R-Tec Страницы: 14
ICStation EQKIT Manual preview
EQKIT
Бренд: ICStation Страницы: 3
CAME BIANCA-VC Installation Manual preview
BIANCA-VC
Бренд: CAME Страницы: 32
JLCooper Electronics SloMoPro User Manual preview
SloMoPro
Бренд: JLCooper Electronics Страницы: 11
Hanna Instruments HI 9912 Instruction Manual preview
HI 9912
Бренд: Hanna Instruments Страницы: 28
Bard CompleteStat CS9B-THOA Quick Start Manual preview
CompleteStat CS9B-THOA
Бренд: Bard Страницы: 10
Aaeon TKS-G20-LN05 Manual preview
TKS-G20-LN05
Бренд: Aaeon Страницы: 54
Elan gSC2 Quick Install Manual preview
gSC2
Бренд: Elan Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды