manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

Miscellaneous registers (Misc)

RM0082

260/844

Doc ID 018672 Rev 1

12.4.39 Diagnostic 

functionality

12.4.40 SYSERR_CFG_CTR register

The SYSERR_CFG_CTR is an R/W register which configures the SoC internal error 
detections. The register bit assignments is detailed in the next table.

         

Table 192.

SYSERR_CFG_CTR register bit assignments

SYSERR_CFG_CTR Register

0x11C

Bit

Name

Reset 
Value

Description

[31:29]

RFU

-

Reserved for future use (Write don’t care - Read return 
zeros).

[28]

DMA_err

1’h0

DMA transfer error (RO); detection enable through 
‘DMA_err_enb’ register field set high:

1’b0: No error pending.

1’b1: Active DMA transfer error; asserted when DMA master 
transaction receives an error response type (for further detail 
ref. DMA Chapter)

[27]

Mem_err

1’h0

Memory transaction error (RO); detection enable through 
'mem_err_enb' register field set high:

1’b0: No error pending.

1’b1: Memory transfer error; asserted from memory 
controller when one of the following error event is active:

A single access outside the defined PHYSICAL memory 
space.

Multiple accesses outside the defined PHYSI-CAL memory 
space.

DRAM initialization completes (no error event).

Address cross page boundary.

DLL unlock event.

[26]

[25]

[24]

usbh2_err

usbh1_err

usbdv_err

1’h0

1’h0

1’h0

USB2 PHY receiver error (RO); detection enable through 
'usb_err_enb' register field set high:

1’b0: No error pending.

1’b1: USB2 PHY 'rxerror'; asserted when one of the 
following error events is active:

Bit stuff errors during FS receive operation.

Elasticity buffer overrun/under run.

Alignment error; EOP not on a byte boundary.

[23]

RFU

-

Reserved for future use (Write don’t care - Read return 
zeros).

[22]

arm1_wdg_err

1’h0

Processors watch dog timeout error (RO); detection enable 
through 'wdg_err_enb' bit set high:

1’b0: No error pending.

1’b1: Active watches dog timeout error; asserted when the 
arms watch dog timer expires (the ARM watch dog 
functionality is supplied from Basic subsystem Timer1).

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

Faulhaber MC 5004 Technical Manual preview
MC 5004
Бренд: Faulhaber Страницы: 66
Kamstrup M-Bus Manual preview
M-Bus
Бренд: Kamstrup Страницы: 36
ABB RHD8000 Series Instructions Manual preview
RHD8000 Series
Бренд: ABB Страницы: 17
Festo CPS-Gate Operating Instructions Manual preview
CPS-Gate
Бренд: Festo Страницы: 109
Topworx Valvetop DXP Installation, Operation & Maintenance Manual preview
Valvetop DXP
Бренд: Topworx Страницы: 8
LAB-EL LB-762 Installation Manual preview
LB-762
Бренд: LAB-EL Страницы: 25
SMC Networks ITV 0 Series Instruction Manual preview
ITV 0 Series
Бренд: SMC Networks Страницы: 2
Oilon VSi 6-14 Installation And Operation Manual preview
VSi 6-14
Бренд: Oilon Страницы: 74
PROEL LED POWER RGB User Manual preview
LED POWER RGB
Бренд: PROEL Страницы: 34
Epsolar LS1024RP Instruction Manual preview
LS1024RP
Бренд: Epsolar Страницы: 32
Watlow DB10-02C0-0000 User Manual preview
DB10-02C0-0000
Бренд: Watlow Страницы: 12
Magtek DYNAMAX Quick Installation Manual preview
DYNAMAX
Бренд: Magtek Страницы: 2
C Prox Ltd FP1-PROX User Manual preview
FP1-PROX
Бренд: C Prox Ltd Страницы: 11
Zaxcom ZFR200 User Manual preview
ZFR200
Бренд: Zaxcom Страницы: 29
PERCo CL-05.2 Operation Manual preview
CL-05.2
Бренд: PERCo Страницы: 42
Tescom 44-4600 Series Instructions For Use Manual preview
44-4600 Series
Бренд: Tescom Страницы: 6
Honeywell IDENT-KEY 3 Operating Manual preview
IDENT-KEY 3
Бренд: Honeywell Страницы: 16
Honeywell VISTA CA-FP-100F User Manual preview
VISTA CA-FP-100F
Бренд: Honeywell Страницы: 46

Бренды по названию

Популярные бренды

Загрузить еще бренды