manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

RM0082

RS_Color liquid crystal display controller (CLCD)

Doc ID 018672 Rev 1

753/844

[25:16]

CPL

10’h0

Clocks per line. This field specifies the number of actual CLCP 
clocks to the LCD panel on each line. This is the number of PPL 
divided by 1 for TFT, 4 or 8 for mono passive, or 2 2/3 for color 
passive, minus one. This must be correctly programmed in 
addition to PPL for the LCD controller to work correctly.

[15]

-

-

Reserved, do not modify, read as zero, write as zero.

[14]

IEO

1’h0

Invert output enable:

1’b0 = 

CLAC

 output pin is active HIGH in TFT mode

1’b1 = 

CLAC

 output pin is active LOW in TFT mode.

The invert output enable (IOE) bit is used to select the active 
polarity of the output enable signal in TFT mode. In this mode, 
the CLAC pin is used as an enable that indicates to the LCD 
panel when valid display data is available. In active display 
mode, data is driven onto the LCD data lines at the programmed 
edge of CLCP when CLAC is in its active state.

[13]

IPC

1’h0

Invert panel clock:

1’b0 = Data is driven on the LCDs data lines on the rising-edge 
of 

CLCP

1’b1 = Data is driven on the LCDs data lines on the falling-edge 
of 

CLCP

.

The IPC bit is used to select the edge of the panel clock on 
which pixel data is driven out onto the LCD data lines.

[12]

IHS

1’h0

Invert horizontal synchronization:

1’b0 = 

CLLP

 pin is active HIGH and inactive LOW

1’b1 = 

CLLP

 pin is active LOW and inactive HIGH.

The invert HSync (IHS) bit is used to invert the polarity of the 
CLLP signal.

[11]

IVS

1’h0

Invert vertical synchronization:

1’b0 = 

CLFP

 pin is active HIGH and inactive LOW

1’b1 = 

CLFP

 pin is active LOW and inactive HIGH.

The invert VSync (IVS) bit is used to invert the polarity of the 
CLFP signal.

[10:06]

ACB

5’h0

AC bias pin frequency. The AC bias pin frequency is only 
applicable to STN displays, which require the pixel voltage 
polarity to be periodically reversed to prevent damage due to DC 
charge accumulation. Program this field with the required value 
minus 1 to apply the number of line clocks between each toggle 
of the AC bias pin, 

CLAC

. This field has no effect if the CLCD is 

operating in TFT mode when the 

CLAC

 pin is used as a data 

enable signal.

[05]

CLKSEL

1’h0

This bit drives the CLCDCLKSEL signal that is used as the 
select signal for the external CLCDCLK clock multiplexer.

1’b0 - HCLK

1’b1 - Other Clock

Table 678.

LCDTiming2 register bit assignments (continued)

Bit

Name

Reset 
value

Description

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

Unipulse F160 Operation Manual preview
F160
Бренд: Unipulse Страницы: 99
Mainpine EPC Operating Instructions Manual preview
EPC
Бренд: Mainpine Страницы: 16
Danfoss AFP Series Installation Manual preview
AFP Series
Бренд: Danfoss Страницы: 20
Samson 3430 Operating Instructions Manual preview
3430
Бренд: Samson Страницы: 52
Samson 3275 Mounting And Operating Instructions preview
3275
Бренд: Samson Страницы: 32
Danfoss Cascade Operating Instructions Manual preview
Cascade
Бренд: Danfoss Страницы: 59
Raypak RayTemp Installation & Operating Instructions Manual preview
RayTemp
Бренд: Raypak Страницы: 24
J+J S 20 Handbook preview
S 20
Бренд: J+J Страницы: 91
SOMFY Situo 1 RTS Installation And Operating Manual preview
Situo 1 RTS
Бренд: SOMFY Страницы: 112
Congatec SMARC conga-SMX8-X Quick Start Manual preview
SMARC conga-SMX8-X
Бренд: Congatec Страницы: 8
MT-Propeller P-8S Series Operation And Installation Manual preview
P-8S Series
Бренд: MT-Propeller Страницы: 16
Topcon OPUS A3 Eco Get Started preview
OPUS A3 Eco
Бренд: Topcon Страницы: 9
Pixsys ATR226 User Manual preview
ATR226
Бренд: Pixsys Страницы: 24
Linear Technology LTC4232 Demo Manual preview
LTC4232
Бренд: Linear Technology Страницы: 6
Airone MTY Mounting Instructions preview
MTY
Бренд: Airone Страницы: 2
National Instruments NI cRIO-9025 User Manual And Specifications preview
NI cRIO-9025
Бренд: National Instruments Страницы: 20
Eliweli EW-601 Instructions For Use preview
EW-601
Бренд: Eliweli Страницы: 2
Kathrein ALC Instructions For Use Manual preview
ALC
Бренд: Kathrein Страницы: 116

Бренды по названию

Популярные бренды

Загрузить еще бренды