Allen-Bradley ProcessLogix 1757-PLX52 Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 24

Allen-Bradley ProcessLogix 1757-PLX52 Скачать руководство пользователя страница 1

Publication 1757-5.1 - August 1999

Installation Instructions

ProcessLogix Hardware

(Cat. No. 1757-PLX52)

This document tells you how to install the components of the ProcessLogix™
system, including the:

•

chassis and power supply

•

1756-CNB ControlNet communication module

•

1757-PLX52 Process Controller module

•

I/O modules

•

ProcessLogix server

•

ControlNet cabling

We also help you to understand installation requirements.

TIP

Fo

For installation information and specifications for the Redundancy
Module, refer to publication 1757-5.15 (shipped with the
1757-SRM Redundancy Module).

For specifications for each module in your system, refer to the
documentation that was shipped with the module(s).

IMPORTANT

The 1757-PLX52 Process Controller module is supplied with only
the boot code installed. You must configure the module before
you can use it in your system. Refer to the ProcessLogix Software
Installation Manual, publication 1757-5.74, for more information.

Allen-Bradley Automation

1
2
3
...
»

Содержание ProcessLogix 1757-PLX52

























Отзывы:

Нет отзывов