manualshive.com logo in svg

Allen-Bradley ProcessLogix 1757-PLX52, Руководство по установке, Страница: 23 / 24

Поделиться
Скачать
Allen-Bradley ProcessLogix 1757-PLX52 Скачать руководство пользователя страница 23

ProcessLogix Hardware

23

Publication 1757-5.1 - August 1999

Specifications

Parameter

Operative and Storage Limits

Transportation Band

Ambient Temp Range

0 to +60°C no fans

-40 to 85°C

Temp. Rate of Change

≤

1°C/min.

≤

5°C/min.

Relative Humidity
(non-condensing)

5 to 95%

5 to 95%

Vibration (3 axes)
Frequency
Acceleration
Displacement

10 to 60 Hz
0.5 g max.
0.1 inches

10 to 60 Hz
1 g max.
0.1 inches

Mechanical Shock
Acceleration
Duration

5 g max.
30 ms max.

20 g max.
30 ms max.

Barometric Pressure
Altitude

-300 to +3000 m

Any

Corrosives

G2 std, G3 option (ISA S71.04)

G3

Module Power Requirements

+5 VDC +/- 5% @ 1.5 A
+3.3 VDC +/- 5% @ 1.0 A

Module Battery Backup Time
Lithium Battery (standard,
built in)

Battery Extension Module
(1757-BEM)

144 hours (non-rechargeable,
replaceable) - 6 days
120 hours (rechargeable) - 5 days

Lithium battery is
disconnected during
shipment.

Removal/Insertion under
power (RIUP)

NOT PERMITTED when
equipment is installed in a Class I,
Division 2, Hazardous (Classified)
Location.
PERMITTED when equipment is
installed in ordinary, non-hazardous,
locations (I/O modules reload
automatically)

CE Conformity (Europe)

89/336/EEC, EMC Directive
EN 50081-2, Emissions, Industrial
EN 50082-2, Immunity, Industrial

N/A

Agency Certifications
When product is marked:

marked for all applicable directives

Class I Div 2 Hazardous

(1)

(1)

CSA certification - Class I, Division 2, Group A,B,C,D or nonhazardous locations

or

Allen-Bradley Automation

Содержание ProcessLogix 1757-PLX52

























Отзывы:

Нет отзывов