background image

ProcessLogix Hardware

13

Publication 1757-5.1 - August 1999

Setting up and Configuring the Server

To use the server (cat. no. 1757-PLXC) in your ProcessLogix system, you must:

connect server hardware

start and log in to the server

verify RSLinx

 communication software configuration and the ControlNet 

server address

verify Ethernet

 adapter and TCP/IP address

Connect Server Hardware

1.

To connect the server hardware, refer to the Dell PC startup documentation 
that accompanied the server.

2.

To install the 9904-KTCX15B card in your server, refer to the 9904-KTCX15B 
installation instructions that accompanied your card.

3.

Once you have connected the hardware, apply power to the server, and 
ensure that it operates correctly.

Start and Log in to the Server

1.

Apply power to the server (if you have not done so already).

2.

At the login screen, type the following:

Verify RSLInx Communication Software Configuration

To communicate with ControlNet devices, your server must have:

RSLinx communication software properly configured

an operating KTC driver

After you have successfully logged on to your server for the first time, make sure 
that RSLinx communication software is properly configured, and your server has a 
valid address for communication with ControlNet devices. Each ControlNet device 

in this field

enter

User Name

administrator

Password

password

Allen-Bradley Automation

Содержание ProcessLogix 1757-PLX52

























Отзывы: