manualshive.com logo in svg

Fujitsu MB86R02, Руководство по оборудованию

Желаете получить подробное описание и инструкцию по эксплуатации устройства Fujitsu MB86R02? На нашем сайте вы можете бесплатно скачать Hardware Manual для этого продукта. Посетите manualshive.com и ознакомьтесь с руководством пользователя прямо сейчас!

Поделиться
Скачать
background image

 

 

15-17 

MB86R02 ‘Jade-D’ Hardware Manual V1.64 
 

 

Restrictions 

When DMA transfer is performed by an external (DREQ) or peripheral (IDREQ) request, there 
are restrictions for external and peripheral signal pins.    

 

 

1.

 DREQ/IDREQ 

DREQ/IDREQ must be asserted for at least 2 cycles of the AHB clock 

(

HCLK). 

There is no restriction for the timing of negating DREQ/IDREQ.   

 

After asserting DACK/IDACK, DMAC is able to accept new a transfer request (edge of 
DREQ/IDREQ) for the next DMA transfer. 

 

 

2.

 DACK/IDACK 

After the DMAC transfers data to the destination address, DACK/IDACK are asserted for 1 
cycle of the AHB clock (HCLK). If access to the destination is executed correctly, this signal 
is asserted. If destination issues, error, retry or split responses occur on the AHB, it is not 
asserted.

 

 
In block transfer mode, these signals indicate that the DMAC has correctly performed 
destination access.   

 

3.

 DEOP (Data End Operation)/IDEOP 

Basically, DEOP/IDEOP is asserted for 1 AHB clock (HCLK) cycle if the DMAC terminates 
DMA transfer properly or abnormally. Abnormal DMA transfer includes the following cases: 

•

  Forced termination by DSTP/IDSTP   

•

  Forced termination by setting 1'b0 to DMACA/EB   

•

  Reception of an error response from the source/destination 

 

4.

 DSTP (Data Stop)/IDSTP 

DSTP/IDSTP are used to forcibly terminate DMA transfer and asserting them during the 
transfer is permitted (it is also permissible to assert DSTP/IDSTP while DMA data is not 
transferred due to a transfer gap or an interrupt function). 
If these signals are used to forcibly terminate DMA transfer, they are not asserted until 
DEOP/IDEOP are asserted.   

 

5.

 Exceptional operation of DEOP/IDEOP

 

If DSTP/IDSTP are asserted immediately after asserting DREQ/DSTP, the DMAC may 
request the bus to execute an IDLE transfer. In this case, the DMAC may assert 
DEOP/IDEOP for 2 or more cycles of the AHB clock (HCLK).

 

The assertion period of DEOP/IDEOP depends on the number of previous master transfer 
cycles. Figure 15-2 shows an example of this exception operation. 
 

Содержание MB86R02





























































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MB86R02

KELCO F60 Installation Instructions Manual preview
F60
Бренд: KELCO Страницы: 36
Lattice Semiconductor MachXO5-NX Development Kit Quick Start preview
MachXO5-NX Development Kit
Бренд: Lattice Semiconductor Страницы: 2
Magnescale LY71 Manual preview
LY71
Бренд: Magnescale Страницы: 3
Idex Pulsafeeder MPC Vector Installation, Operation & Maintenance Manual preview
Pulsafeeder MPC Vector
Бренд: Idex Страницы: 114
Shimaden PAC18A Series Instruction Manual preview
PAC18A Series
Бренд: Shimaden Страницы: 32
Renogy Rover 100A Manual preview
Rover 100A
Бренд: Renogy Страницы: 36
SKF Ecomag Installation, Operation And Maintenance Manual preview
Ecomag
Бренд: SKF Страницы: 11
Danfoss VT2800 Series Design Manual preview
VT2800 Series
Бренд: Danfoss Страницы: 162
Rare Waves Grendel 2TAC Manual preview
Grendel 2TAC
Бренд: Rare Waves Страницы: 18
LAMBERTI ELEKTRONIK Latherm HZR Comfort Operating Manual preview
Latherm HZR Comfort
Бренд: LAMBERTI ELEKTRONIK Страницы: 16
3M Touch Screen Controller SX112 Reference Manual preview
Touch Screen Controller SX112
Бренд: 3M Страницы: 33
Kontron M2M Smart Service Developer Kit Getting Started Manual preview
M2M Smart Service Developer Kit
Бренд: Kontron Страницы: 27
OK-I PTZ-KB050 Operational Manual preview
PTZ-KB050
Бренд: OK-I Страницы: 10
Warner Electric CBC-150 Series Installation And Operation Manual preview
CBC-150 Series
Бренд: Warner Electric Страницы: 4
Rain Evo 1 Instructions Manual preview
Evo 1
Бренд: Rain Страницы: 8
Autopilot ECLIPSE F90 User Manual preview
ECLIPSE F90
Бренд: Autopilot Страницы: 12
Embedded Systems LogicMachine Reactor Lite Quick Start Manual preview
LogicMachine Reactor Lite
Бренд: Embedded Systems Страницы: 7
second sound ACO160 Quick Start Manual preview
ACO160
Бренд: second sound Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды