Fujitsu MB86R02 Скачать руководство пользователя | Manualshive

Страница: 300 / 892

background image

16-1

MB86R02 ‘Jade-D’ Hardware Manual V1.64

16 Host Interface

This chapter describes the Host Interface of the MB86R02.

16.1.

Outline

The Host Interface module is an internal module connected to the AHB which is used for
communication to an external host CPU (which is connected via the SPI interface). The host
CPU can read and write to the internal module. From a host CPU point of view, this module
functions as a slave, whereas it functions as a master internally.

16.2.

Features

The Host Interface has the features described in the following sections.

16.2.1.

Features

Accesses by the host CPU to the internal module can made using varying address bytes lengths
within a range of 1 to 4 bytes. Additionally, the data byte length can be arbitrarily set within a
range of 1 to 16 bytes. This means that the received number of bytes can be optimized and that
forwarding can be done efficiently. These settings can be specified by the CMD byte, allowing a
highly flexible solution that abstracts the type of host CPU in use and the access objects.



Supports communication to a host CPU with an SPI interface



The length of the SPI interface packets is variable to permit the use of variable length
addresses and data accesses



Supports writes/reads to the internal module connected to the AHB (variable, from 1 to 16
bytes)



Conforms to Freescale Semiconductor's advocacy SPI (CPOL=0, CPHA=0)



Corresponds to the speed of general purpose CPUs (set the frequency of SPICLK to 1/2 or
less of the HCLK frequency)



Host CPU handshaking communication makes software flow control possible

16.2.2.

Limitations



The MB86R02 can only operate in slave mode whereas the host CPU is the bus master



The packet sizes must be in 8 bit units



No CRC error detection functionality.



No automatic procedure for resends in the case of errors (no ARQ functionality)



Supported burst transfer modes for the AHB are single, incr or incr4

«
...
298
299
300
301
302
...
»

Содержание MB86R02





























































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MB86R02

Бренд: Fantech Страницы: 2

MachXO5-NX Development Kit

Бренд: Lattice Semiconductor Страницы: 2

Бренд: Rain Bird Страницы: 4

Бренд: Rain Bird Страницы: 2

Бренд: Rain Bird Страницы: 140

WeatherSmart RSC600i

Бренд: Raindrip Страницы: 36

Бренд: L-Acoustics Страницы: 24

Бренд: L-Acoustics Страницы: 21

Бренд: +GF+ Страницы: 3

Бренд: Gardena Страницы: 236

Бренд: Data Signs Страницы: 23

Бренд: Computer Automation Technology Страницы: 55

Бренд: Harman Страницы: 2

Бренд: Linear Technology Страницы: 6

8745 MFC Ethernet

Бренд: Burkert Страницы: 70

Бренд: OLYS Страницы: 4

The Boost Box WS 1107

Бренд: Watersports Innovations Страницы: 12

Бренд: Parker Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды