Cisco MDS 9000 Series Скачать руководство пользователя страница 704

Страница: 704 / 1640

S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m

11-98

Cisco MDS 9000 Family Command Reference

OL-18089-01, Cisco MDS NX-OS Release 4.x

Chapter 11 I Commands

iscsi virtual-target name

To create a static iSCSI virtual target, use the

iscsi virtual-target

command. To revert to the default

values, use the

form of the command.

iscsi virtual-target name

name

advertise interface

{

gigabitethernet

slot

port

[

subinterface

]

port-channel

channel-id

[

subinterface

]}

all-initiator-permit

initiator

{

initiator-name

ip-address

ipaddress

[

netmask

]}

permit

pwwn

pwwn-id

[

fc-lun

number

iscsi-lun

number

[

secondary-pwwn

pwwn-id

[

sec-lun

number

]] |

secondary-pwwn

pwwn-id

]

revert-primary-port

trespass

iscsi virtual-target name

name

no advertise interface

{

gigabitethernet

slot

port

[

subinterface

]

port-channel

channel-id

[

subinterface

]}

no all-initiator-permit

no initiator

{

initiator-name

ip-address

ipaddress

[

netmask

]}

permit

no pwwn

pwwn-id

[

fc-lun

number

iscsi-lun

number

[

secondary-pwwn

pwwn-id

[

sec-lun

number

]] |

secondary-pwwn

pwwn-id

]

no revert-primary-port

no trespass

no iscsi virtual-target name

name

Syntax Description

name

Enters the virtual target name to be used. The minimum length is 16
characters and maximum of 223 bytes.

advertise interface

Advertises the virtual target name on the specified interface.

gigabitethernet

slot

port

subinterface

]

Selects the Gigabit Ethernet interface or subinterface to configure.

port-channel

channel-id

subinterface

]

Selects the Port Channel interface or subinterface to configure.

all-initiator-permit

Enables all iSCSI initiator access to this target.

initiator

Configures specific iSCSI initiator access to this target.

initiator-name

Specifies the iSCSI initiator name to be used access a specified target.
Maximum length is 255 characters.

ip-address

ip-address

Specifies the iSCSI initiator IP address.

ip-subnet

Specifies all initiators in the subnet.

permit

Permits access to the specified target.

pwwn

pwwn-id

Specifies the peer WWN ID for special frames.

secondary-pwwn

pwwn-id

Specifies the secondary pWWN ID.

fc-lun

number

Specifies the Fibre Channel Logical Unit Number (LUN).

iscsi-lun

number

Specifies the iSCSI virtual target number.

sec-lun

number

Specifies the secondary Fibre Channel LUN.

trespass

Moves LUNs forcefully from one port to another.

Содержание MDS 9000 Series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MDS 9000 Series

Отзывы:

Похожие инструкции для MDS 9000 Series

Бренды по названию

Популярные бренды

Cisco MDS 9000 Series, Справочник по командам

Результаты поиска

Содержание MDS 9000 Series

Отзывы:

Похожие инструкции для MDS 9000 Series

Бренды по названию

Популярные бренды