Chevrolet 10 Series 1970, Руководство по обслуживанию

Страница: 352 / 671

ENGINE 6-30
F ig „ 3 V —A ir A d a p te r Tool
4. Using T o o l J-5892 to com p ress the va lv e spring,
rem o ve the va lve locks, va lve cap (o r rota tor) and
v a lv e spring and dam per (fig . 4 V ).
5. R em ove the va lve stem o il seal.
6. A ssem b le as follow s:
Sm all V8 Engines
a„ Set the va lve spring and dam per, va lve shield and
v a lve cap (or -rotator) in place. The c lo se coiled
end o f the spring is in stalled against the cylin der
head. C om p ress the spring with T o o l J-5892 and
install o il seal in the lo w er g ro o ve o f the stem ,
making sure the seal is flat and not twisted.
NQTE: A light coat o f o il on the seal w ill help
p reven t tw isting.
b. Install the v a lv e locks and re le a s e the com ­
p re s s o r tool making sure the locks seat p ro p erly
in the upper gro o ve o f the va lve stem .
NOTE: G rease may be used to hold the locks in
place while relea sin g the com p resso r tool.
M ark IV V8 Engines
a. Install new valve stem o il seal (coated with o il)
in position over va lve guide.
b. Set the rotator (exhaust v a lv e ), va lve spring and
dam per and valve cap in place,
c. C om press the spring with T o o l J-5892 and install
the va lve locks then re le a s e the c o m p resso r tool,
making sure the locks seat p ro p e rly in the gro o ve
o f the va lve stem.
NOTE: G rease may be used to hold the locks
in place while re lea sin g the c o m p resso r tool.
7. Install spark plug, using a new gasket on 13/16"
plugs and torque to specification s.
8. Install and adjust va lve mechanism as outlined.
C ylinder Head Assembly
Removal
1. R em ove intake m anifold as outlined.
2. Rem ove exhaust m anifolds as outlined.
3. R em ove va lve mechanism as outlined.
4. D rain cylin der block o f coolant.
5. R em ove cylin d er head bolts, cylin d er head and g a s ­
ket. P la c e cylin d er head on two blocks o f wood to
preven t damage.
Installation
CA UTIO N: The gaskets su rfaces on both the
head and the block must be clean o f any fo reign
m atter and fr e e o f nicks o r heavy scratch es.
C ylin der bolt threads in the block and threads on
the cylin der head bolts must be clean. (D irt w ill
a ffe c t bolt torque).
1. On engines using a S T E E L gasket, coat both sides of
a new gasket with a good s e a le r. Spread the se a le r
thin and even. One method o f applying the sea le r
that w ill assure the p rop er coat is with the use o f a
paint r o lle r . T oo much s e a le r may hold the gasket
away fro m the head o r block.
CA U TIO N :
Use no se a le r on engines using a
com position S T E E L ASBESTOS gasket.
2. P la c e the gasket in position o v e r the dowel pins with
the bead up.
3. C arefu lly guide the cylin der head into place o v e r the
dowel pins and gasket.
4. Coat threads o f cylin d er head bolts with sealing
compound and in stall bolts fin g er tight.
5. Tighten each cylin d er head bolt a little at a tim e in
the sequence shown in the torque sequence chart until
the sp ecified torque is reached.
6. Install exhaust m anifolds as outlined.
7. Install intake m anifold as outlined.
8. Install and adjust va lve mechanism as outlined.
O il Pan
F ig . 4 V —•Compressing V a lv e Spring
Removal
1. D rain engine oil.
CHEVROLET TRUCK SERVICE MANUAL