Oki ES9160, Maintenance Manual

Page: 496 / 1087

ES9160 MFP / ES9170 MFP © 2012 OKI DATA CORPORATION All rights reserved
ERROR CODE AND TROUBLESHOOTING
8 - 16
CBA0 Finisher related
service call Front saddle stapler home position error: The stapler
home position detection is abnormally operated and
finished. [MJ-1106] P. 8-158
CBB0 Rear saddle stapler home position error: The
stapler home position detection is abnormally
operated and finished. [MJ-1106] P. 8-158
CBC0 Saddle Stitch Finisher side alignment motor (M15)
abnormality: The alignment motor is not rotating or
the alignment plate is not working properly. [MJ-
1106] P. 8-158
CBE0
Saddle Stitch Finisher folding motor (M17)
abnormality: The folding motor is not rotating or the
folding roller is not moving normally. [MJ-1106]
P. 8-159
CBF0 Stacker motor (M9) abnormality :
The stacker motor is not rotating. [MJ-1033] P. 8-160
CC01 A model not supporting the Finisher is connected. Note
that this error is recognized in the communication
converter and is output. -
CC02 Stack exit roller nip home position detection error: The
detection of the home position of the stack exit roller nip
ends abnormally. [MJ-1032/MJ-1033] P. 8-160
CC20 Saddle communication error [MJ-1106] P. 8-161
CC21 The detection of the home position of the saddle stitch
3rd transport roller drive motor ends abnormally. P. 8-161
CC22 The detection of the home position of the saddle stitch
stapler unit ends abnormally. P. 8-162
CC23 An abnormal interruption of the encoder pulse of the
folding blade occurrs.
-
CC30
Stack transport motor abnormality: The stack
transport motor is not rotating or the stack transport
belt is not moving normally. [MJ-1101/MJ-1106]
P. 8-163
CC31 Transport motor abnormality: The transport motor is
not rotating or the stack transport roller -1 and -2 is
not rotating normally. [MJ-1101/MJ-1106] P. 8-163
CC41 Paper holder cam home position abnormality: The
paper holder cam is not at the home position. [MJ-
1101] P. 8-164
CC51 Sideways adjustment motor (M2) abnormality:
Sideways adjustment motor is not rotating or
puncher is not shifting normally. [MJ-1101/MJ-1106
(when MJ-6103 is installed)] P. 8-165
CC52 Skew adjustment motor (M1) abnormality: Skew
adjustment motor is not rotating or puncher is not
shifting normally. [MJ-1101/MJ-1106 (when MJ-
6103 is installed)] P. 8-166
CC53 An abnormality occurs in the punch waste full sensor. P. 8-167
CC54 Hole punch registration sensor detection error: An
abnormality occurs in the hole punch registration sensor.
[MJ-1032/MJ-1033] P. 8-167
CC60 Punch motor abnormality: Punch motor is not rotating or
puncher is not shifting normally.] P. 8-170
CC61 Punch motor (M3) home position detection error: Punch
motor is not rotating or puncher is not shifting normally.
[MJ-1101/MJ-1106 (when MJ-6103 is installed)] P. 8-170
CC71 Punch ROM checksum error: Abnormality of checksum
value on Hole punch controller PC board is detected
when the power is turned on. [MJ-1101/MJ-1106 (when
MJ-6103 is installed)] P. 8-171
Error code Classification Contents Troubleshooting