Oki ES9160, Maintenance Manual, Page: 494 / 1087

ES9160 MFP / ES9170 MFP © 2012 OKI DATA CORPORATION All rights reserved
ERROR CODE AND TROUBLESHOOTING
8 - 14
CB00 Finisher related
service call Finisher not connected P. 8-140
CB01 Finisher communication error P. 8-140
CB10 Entrance motor abnormality: The entrance motor is not
rotating normally. [MJ-1101/MJ-1106] P. 8-140
CB11 Buffer tray guide motor abnormality: The buffer tray guide
motor is not rotating or the buffer tray guide is not moving
normally. [MJ-1101/MJ-1106] P. 8-141
CB12 Buffer roller drive motor abnormality: The buffer roller
drive motor is not rotating or the buffer roller is not moving
normally. [MJ-1101/MJ-1106] P. 8-141
CB13
Finisher exit motor abnormality [MJ-1101/MJ-1106] P. 8-142
CB14
Paper holding arm motor abnormality [MJ-1101/MJ-1106] P. 8-142
CB30 Movable tray shift motor abnormality: The movable tray
shift motor is not rotating or the movable tray is not
moving normally. [MJ-1101]
Movable tray shift motor abnormality: The movable tray
shift motor or the movable tray does not work properly.
[MJ-1032]
Movable tray shift motor abnormality: The movable tray
shift motor or the movable tray does not work properly.
[MJ-1033]
P. 8-143
P. 8-144
P. 8-145
CB31 Movable tray paper-full detection error: The actuator of
the movable tray paper-full detection sensor does not
move smoothly. [MJ-1101/MJ-1106] P. 8-145
CB40 Front alignment motor abnormality: The front alignment
motor is not rotating or the front align/1106ment plate is
not moving normally. [MJ-1101]
Front alignment plate home position detection error: The
detection of the home position ends abnormally because
the front alignment plate has not worked properly.
[MJ-1032/MJ-1033]
P. 8-146
P. 8-148
CB50 Stapler home position error: The stapler home position
sensor does not work. [MJ-1101/MJ-1106]
Stapler unit home position detection error: The detection
of the home position of the stapler unit ends abnormally.
[MJ-1032/MJ-1033]
P. 8-148
P. 8-149
P. 8-149
CB51 Stapler shift home position error: The stapler is not at the
home position. [MJ-1101/MJ-1106]
Stapler unit sliding home position detection error: The
detection of the home position of the stapler unit sliding
ends abnormally. [MJ-1032/MJ-1033]
P. 8-150
P. 8-151
P. 8-152
CB60 Stapler shift motor abnormality: Stapler shift motor is not
rotating or staple unit is not moving normally.
[MJ-1101/MJ-1106] P. 8-152
CB80 Backup RAM data abnormality:
Abnormality of checksum value on finisher controller PC
board is detected when the power is turned ON.
[MJ-1101/MJ-1106]
EEPROM data abnormality: An error occurs during the
writing of data into the EEPROM of the Finisher. [MJ-
1032/MJ-1033]
P. 8-153
P. 8-153
CB81 Flash ROM abnormality: Abnormality of checksum value
on finisher controller PC board is detected when the
power is turned ON. [MJ-1101/MJ-1106] P. 8-154
CB82
Finisher - Main CPU program error P. 8-154
Error code Classification Contents Troubleshooting