manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

The following illustration shows cable routing for the DVD cable:

Attention:

Follow the optical drive cable routing as the illustration shows. Make sure that the

cable is not pinched and does not cover any connectors or obstruct any components on the
system board.

Optical drive
connector

Release tab

DVD drive
cable

Cable connector
latch

Figure 179. DVD drive cable routing

Step 6.

Replace the air baffle (see “Replacing the air baffle” on page 242).

Step 7.

Replace the cover (see “Replacing the cover” on page 240).

Step 8.

Slide the server into the rack.

Step 9.

Reconnect the power cords and any cables that you removed.

Step 10. Turn on the peripheral devices and the server.

Removing a tape drive

Use this information to remove a tape drive.

To remove an optional tape drive, complete the following steps:

Chapter 6

.

Removing and replacing components

263

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

Korenix AnyBus-X Installation Leaflet preview
AnyBus-X
Brand: Korenix Pages: 2
Intel SBXL52 - Server Compute Blade Hardware Maintenance Manual preview
SBXL52 - Server Compute Blade
Brand: Intel Pages: 126
IBM BladeCenter HS21 1885 Problem Determination And Service Manual preview
BladeCenter HS21 1885
Brand: IBM Pages: 140
Supermicro SUPERSERVER 5018A-MHN4 User Manual preview
SUPERSERVER 5018A-MHN4
Brand: Supermicro Pages: 116
Jung SV-SERVER-01 Operating Instructions Manual preview
SV-SERVER-01
Brand: Jung Pages: 16
HMS Networks Anybus Communicator ABC4018 User Manual preview
Anybus Communicator ABC4018
Brand: HMS Networks Pages: 64
Conceptronic C54PSERVUM User Manual preview
C54PSERVUM
Brand: Conceptronic Pages: 127
HIKVISION NVR Server User Manual preview
NVR Server
Brand: HIKVISION Pages: 13
RackSolutions 4Post Installation Instructions Manual preview
4Post
Brand: RackSolutions Pages: 8
xFusion Digital Technologies FusionServer G8600 V7 Manual preview
FusionServer G8600 V7
Brand: xFusion Digital Technologies Pages: 112
Supermicro SuperServer 6029U-TR25M User Manual preview
SuperServer 6029U-TR25M
Brand: Supermicro Pages: 151
IEI Technology PUZZLE-IN004 Series User Manual preview
PUZZLE-IN004 Series
Brand: IEI Technology Pages: 102
LOOQS MB202 User Manual preview
MB202
Brand: LOOQS Pages: 69
Black Box les1208A Manual preview
les1208A
Brand: Black Box Pages: 4
Black Box LES1202A Quick Start Manual preview
LES1202A
Brand: Black Box Pages: 12
Red Hat NETWORK SATELLITE 5.3.0 - CHANNEL MANAGEMENT Reference Manual preview
NETWORK SATELLITE 5.3.0 - CHANNEL MANAGEMENT
Brand: Red Hat Pages: 318
Multitech TalkAnytime TA2410 User Manual preview
TalkAnytime TA2410
Brand: Multitech Pages: 235
Meinberg LANTIME M600 MRS User Manual preview
LANTIME M600 MRS
Brand: Meinberg Pages: 160

Brands by name

Popular brands

Load more brands