manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

CIM Information

Prefix:

PLAT

ID:

0524

User Response

1. Make sure that the fans are operating, that there are no obstructions to the airflow (front and

rear of the server), that the air baffle is in place and correctly installed, and that the server cover
is installed and completely closed.

2. Check the ambient temperature. You must be operating within the specifications (see Server

Features and specifications for more information).

3. Make sure that the heat sink for microprocessor n.

4. (Trained technician only) Replace microprocessor n. (n = microprocessor number)

•

80070301-0302ffff : Sensor [SensorElementName] has transitioned to non-recoverable from a

less severe state. (CPU 2 OverTemp)

This message is for the use case when an implementation has detected a Sensor transitioned to
non-recoverable from less severe.

May also be shown as 800703010302ffff or 0x800703010302ffff

Severity

Error

Serviceable

Yes

Automatically notify support

No

Alert Category

Critical - Temperature

SNMP Trap ID

0

CIM Information

Prefix:

PLAT

ID:

0524

User Response

1. Make sure that the fans are operating, that there are no obstructions to the airflow (front and

rear of the server), that the air baffle is in place and correctly installed, and that the server cover
is installed and completely closed.

2. Check the ambient temperature. You must be operating within the specifications (see Server

Features and specifications for more information).

3. Make sure that the heat sink for microprocessor n.

4. (Trained technician only) Replace microprocessor n. (n = microprocessor number)

•

8007030d-2b81ffff : Sensor [SensorElementName] has transitioned to non-recoverable from a less

severe state. (FDIMM Endurance)

Appendix A. Integrated management module II (IMM2) error messages

467

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

NEC Univerge SV8100 System Specifications preview
Univerge SV8100
Brand: NEC Pages: 2
IBM BladeCenter HS23 Service Manual preview
BladeCenter HS23
Brand: IBM Pages: 36
Paradyne FrameSaver SLV 9126 Installation Instructions Manual preview
FrameSaver SLV 9126
Brand: Paradyne Pages: 24
Newtec NOP1840 PEP-Box User Manual preview
NOP1840 PEP-Box
Brand: Newtec Pages: 96
IBM BladeCenter PS703 Technical Overview And Introduction preview
BladeCenter PS703
Brand: IBM Pages: 198
Supero SuperServer 6123L-8R User Manual preview
SuperServer 6123L-8R
Brand: Supero Pages: 105
Obvius AcquiLite EMB A7810 Installation And Operation Manual preview
AcquiLite EMB A7810
Brand: Obvius Pages: 29
Edimax Past Ethernet Combo Print Server PS-1216U Quick Installation Manual preview
Past Ethernet Combo Print Server PS-1216U
Brand: Edimax Pages: 23
Acer Aspire EASYSTORE H341 Quick Start Manual preview
Aspire EASYSTORE H341
Brand: Acer Pages: 59
Acer Aspire EASYSTORE H341 Service Manual preview
Aspire EASYSTORE H341
Brand: Acer Pages: 74
Acer Aspire EasyStore Series User Manual preview
Aspire EasyStore Series
Brand: Acer Pages: 148
Acer Aspire easyStore H340 Service Manual preview
Aspire easyStore H340
Brand: Acer Pages: 68
Acer Altos EasyStore User Manual preview
Altos EasyStore
Brand: Acer Pages: 169
Acer Aspire easyStore H340 User Manual preview
Aspire easyStore H340
Brand: Acer Pages: 148
Acer Altos EasyStore Quick Installation Manual preview
Altos EasyStore
Brand: Acer Pages: 7
Dell PowerEdge 400SC Update preview
PowerEdge 400SC
Brand: Dell Pages: 1
QNAP TVS-1272XU-RP User Manual preview
TVS-1272XU-RP
Brand: QNAP Pages: 53
IBM BladeCenter HS22 Supplementary Manual preview
BladeCenter HS22
Brand: IBM Pages: 1

Brands by name

Popular brands

Load more brands