Lenovo x3650 M4 BD 5466 Installation And Service Manual Download Page 143 | Manualshive

Page: 143 / 1222

background image

Installation tool

Microprocessor

Cover

Figure 123. Installation tool cover removal

Note:

Do not touch the microprocessor contacts. Contaminants on the microprocessor

contacts, such as oil from your skin, can cause connection failures between the contacts
and the socket.

c.

Align the installation tool with the microprocessor socket. The installation tool rests flush on
the socket only if properly aligned.

Figure 124. Installation tool alignment

d.

Install the microprocessor using the following instructions for your installation tool.

• If using Installation Tool A, twist the handle on the microprocessor tool assembly

counterclockwise to the open position to insert the microprocessor into the socket, and
lift the installation tool out of the socket.

• If using Installation Tool B, twist the handle of the installation tool assembly counterclockwise

until the microprocessor is inserted into the socket, and lift the installation tool out of the
socket. The following illustration shows the tool handle in the open position.

Installing optional devices

131

«
...
141
142
143
144
145
...
»

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

UniServer T1100 G3

Brand: H3C Pages: 66

UniServer R6900 G3

Brand: H3C Pages: 214

UniServer R6700 G3

Brand: H3C Pages: 151

UniServer R4900 G5

Brand: H3C Pages: 16

ioLogik W5300 Series

Brand: Moxa Technologies Pages: 177

Brand: Obvius Pages: 29

Brand: ASROCK Rack Pages: 51

Brand: AIC Pages: 64

Brand: Speco Pages: 28

ProLiant DL380 Gen9

Brand: HPE Pages: 8

Brand: Time Machines Pages: 24

Brand: Digi Pages: 163

Brand: Asus Pages: 82

Brand: Asus Pages: 32

Brand: Asus Pages: 42

RS100-E5 - 0 MB RAM

Brand: Asus Pages: 148

PIKE II 3008 Series

Brand: Asus Pages: 80

Brand: Asus Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands