Lenovo x3650 M4 BD 5466 Installation And Service Manual Download Page 777

Page: 777 / 1222

•

81010901-1003ffff : Numeric sensor [NumericSensorElementName] going high (upper critical) has

deasserted. (Rear BP Temp)

This message is for the use case when an implementation has detected an Upper Critical sensor going
high has deasserted.

May also be shown as 810109011003ffff or 0x810109011003ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Temperature

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0495

User Response

No action; information only.

•

81010901-1401ffff : Numeric sensor [NumericSensorElementName] going high (upper critical) has

deasserted. (CPU1 VR Temp)

This message is for the use case when an implementation has detected an Upper Critical sensor going
high has deasserted.

May also be shown as 810109011401ffff or 0x810109011401ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Temperature

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0495

User Response

No action; information only.

Appendix A. Integrated management module II (IMM2) error messages

765

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3650 M4 BD 5466

Reviews:

Related manuals for x3650 M4 BD 5466

Brands by name

Popular brands

Lenovo x3650 M4 BD 5466, Installation And Service Manual

Search results

Summary of Contents for x3650 M4 BD 5466

Reviews:

Related manuals for x3650 M4 BD 5466

Brands by name

Popular brands