manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

• One tape drive power cable

• Four M3 x 6 screws

The following illustration shows how to install an optional tape drive.

000

000

000

000

000

000

000

000

Figure 116. Tape drive installation

To install a SATA or USB tape drive, complete the following steps:

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines”
on page 34.

Step 2.

Turn off the server and peripheral devices and disconnect the power cords and all external cables,
if necessary.

Step 3.

Install the tape drive on the tray as shown in the following illustration. If the tape drive comes with a
metal spacer attached, remove the spacer before you install the tape drive on the tray.

Figure 117. Installing the tape drive on the tray

Step 4.

Prepare the drive according to the instructions that come with the drive, setting any switches
or jumpers.

Step 5.

Connect the following tape enablement kit cables to the connectors on the system board:

• SAS signal cables into the SAS connectors on the system board

Chapter 2

.

Installing optional devices

125

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

D-Link ShareCenter DNS-343 Quick Install Manual preview
ShareCenter DNS-343
Brand: D-Link Pages: 12
NEC Express5800/320Ma Software Installation And Configuration Manual preview
Express5800/320Ma
Brand: NEC Pages: 86
Samsung SRD-1670DC Properties preview
SRD-1670DC
Brand: Samsung Pages: 7
Omneon MediaGrid ContentServer 3000 Quick Reference Manual preview
MediaGrid ContentServer 3000
Brand: Omneon Pages: 2
TYANO TS65A-B8036 Service Engineer'S Manual preview
TS65A-B8036
Brand: TYANO Pages: 102
Supero SUPERSERVER 5014C-MT User Manual preview
SUPERSERVER 5014C-MT
Brand: Supero Pages: 112
Advantech DVG-1100 Manual preview
DVG-1100
Brand: Advantech Pages: 43
ZLAN ZLAN5443A User Manual preview
ZLAN5443A
Brand: ZLAN Pages: 13
IBM x3350 - System - 4192 User Manual preview
x3350 - System - 4192
Brand: IBM Pages: 98
IBM x3500 - System - 7977 Installation Manual preview
x3500 - System - 7977
Brand: IBM Pages: 124
IBM System x3250 Installation And User Manual preview
System x3250
Brand: IBM Pages: 106
IBM x3200 - System M3 - 7328 Installation Manual preview
x3200 - System M3 - 7328
Brand: IBM Pages: 100
IBM System x3400 Type 7975 Installation Manual preview
System x3400 Type 7975
Brand: IBM Pages: 124
IBM System x3300 M4 Installation And Service Manual preview
System x3300 M4
Brand: IBM Pages: 470
IBM System x iDataPlex dx360 Manual preview
System x iDataPlex dx360
Brand: IBM Pages: 26
Asus AP1720-E1 User Manual preview
AP1720-E1
Brand: Asus Pages: 78
Asus AP100 Hardware Reference Manual preview
AP100
Brand: Asus Pages: 32
Asus Aaeon AIOT-ILRA01 User Manual preview
Aaeon AIOT-ILRA01
Brand: Asus Pages: 39

Brands by name

Popular brands

Load more brands