manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

Attention:

Do not touch the microprocessor contacts. Contaminants on the microprocessor

contacts, such as oil from your skin, can cause connection failures between the contacts
and the socket.

Step 8.

Remove the microprocessor from the socket.

a.

Select the empty installation tool and ensure that the handle is in the open position. If the
installation tool handle is not in the open position, use the following instructions for your
installation tool:

• If using Installation Tool A, twist the microprocessor installation tool handle counterclockwise

to the open position.

Handle

Installation tool

Figure 238. Installation tool handle adjustment

• If using Installation Tool B,

1

lift the interlock latch and hold it up while you

2

twist the

microprocessor installation tool handle counterclockwise to the open position, and then
release the interlock latch. The following illustration of the installation tool shows the
location of the interlock latch and counterclockwise rotation of the handle before loading
the microprocessor.

H

Figure 239. Installation tool handle adjustment

b.

Align the installation tool with the screws, as shown in the following graphic, and lower the
installation tool on the microprocessor. The installation tool rests flush on the socket only
when it is aligned correctly.

328

Lenovo System x3650 M4 Installation and Service Guide

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

IBM Flex System x440 Compute Node Installation And Service Manual preview
Flex System x440 Compute Node
Brand: IBM Pages: 584
Eaton RS Enclosure Unpacking Manual preview
RS Enclosure
Brand: Eaton Pages: 2
Bull NovaScale R410B F2 Getting Started preview
NovaScale R410B F2
Brand: Bull Pages: 38
Leightronix UltraNEXUS-HD X5 Product Quick Manual preview
UltraNEXUS-HD X5
Brand: Leightronix Pages: 5
B&B Electronics Vlinx VESR4 4 Series User Manual preview
Vlinx VESR4 4 Series
Brand: B&B Electronics Pages: 70
Speco ONSIP OS101 User Manual preview
ONSIP OS101
Brand: Speco Pages: 28
Koon Technology KNTD-100 Manual preview
KNTD-100
Brand: Koon Technology Pages: 20
Bosanova RBT-320 Quick Start Manual preview
RBT-320
Brand: Bosanova Pages: 2
Blonder tongue AQT-RCS Instruction Manual preview
AQT-RCS
Brand: Blonder tongue Pages: 20
Black Box LS4103A User Manual preview
LS4103A
Brand: Black Box Pages: 46
Allnet FW8888 Quick Installation Manual preview
FW8888
Brand: Allnet Pages: 12
Eelectron Horizone Mini IN00M02WEB Installation Manual preview
Horizone Mini IN00M02WEB
Brand: Eelectron Pages: 118
DEVA DB4000 Maintenance And Operation Instruction Manual preview
DB4000
Brand: DEVA Pages: 90
Silicon Graphics International SGI UV 30 User Manual preview
SGI UV 30
Brand: Silicon Graphics International Pages: 68
Silicon Graphics UV 2000 System User'S Manual preview
UV 2000
Brand: Silicon Graphics Pages: 116
TROY Group TROY500 Series Installation And User Manual preview
TROY500 Series
Brand: TROY Group Pages: 35
Plustek eDoc N600 User Manual preview
eDoc N600
Brand: Plustek Pages: 86
Fiery X2 Administrator'S Manual preview
X2
Brand: Fiery Pages: 164

Brands by name

Popular brands

Load more brands