manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

Serviceable

No

Automatically notify support

No

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

202-801-000 : MemStr Test Aborted

Internal program error.

Recoverable

No

Severity

Warning

Serviceable

Yes

Automatically notify support

No

User Response

Complete the following steps:

1. Turn off and restart the system.

2. Make sure that the DSA Diagnostic code is at the latest level.

3. Run the test again.

4. If the system has stopped responding, turn off and restart the system.

5. Check the system firmware level and upgrade if necessary.

6. Run the memory diagnostic to identify the specific failing DIMM.

7. If the failure remains, refer to "Troubleshooting by symptom" in the system "Installation and

Service Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

202-802-000 : MemStr Test Aborted

Memory size is insufficient to run the test. At least 1 GB is required.

Recoverable

No

Severity

Warning

Appendix C. DSA diagnostic test results

1153

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

A10 Networks AX Series Deployment Manual preview
AX Series
Brand: A10 Networks Pages: 17
IBM Z10 BUISNESS CLASS Z10 BC Reference Manual preview
Z10 BUISNESS CLASS Z10 BC
Brand: IBM Pages: 67
IBM x3450 - System - 7948 Quick Start Manual preview
x3450 - System - 7948
Brand: IBM Pages: 2
i3 International SRX-Pro Server Quick Start Manual preview
SRX-Pro Server
Brand: i3 International Pages: 2
IBM HS21 XM BLADECENTER - L5408 FOR SPEC CPU2006 Supplementary Manual preview
HS21 XM BLADECENTER - L5408 FOR SPEC CPU2006
Brand: IBM Pages: 1
H3C UniServer R4300 G5 Installation, Quick Start preview
UniServer R4300 G5
Brand: H3C Pages: 16
Fujitsu Siemens Computers PRIMERGY B120 Operating Manual preview
PRIMERGY B120
Brand: Fujitsu Siemens Computers Pages: 68
Flexport HF2211 User Manual preview
HF2211
Brand: Flexport Pages: 39
IBM xSeries 200VL Installation Manual preview
xSeries 200VL
Brand: IBM Pages: 70
AC&T System ETOS-100XP-E04 User Manual preview
ETOS-100XP-E04
Brand: AC&T System Pages: 32
Hanwha Vision SPA-S2000 Quick Manual preview
SPA-S2000
Brand: Hanwha Vision Pages: 16
NEC N8100-2834F Maintenance Manual preview
N8100-2834F
Brand: NEC Pages: 138
Moxa Technologies 2140 User Manual preview
2140
Brand: Moxa Technologies Pages: 100
IBM @server x Series Quick Setup Manual preview
@server x Series
Brand: IBM Pages: 8
RCI FP-SER-ETH-SERVR2 User Manual preview
FP-SER-ETH-SERVR2
Brand: RCI Pages: 17
SystemBase Portbase-3010 User Manual preview
Portbase-3010
Brand: SystemBase Pages: 118
BITMAIN ANTMINER S19 Pro+ Hydro Installation Manual preview
ANTMINER S19 Pro+ Hydro
Brand: BITMAIN Pages: 17
SAFARI Montage T-440i Installation Manual preview
T-440i
Brand: SAFARI Montage Pages: 8

Brands by name

Popular brands

Load more brands