manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

Serviceable

Yes

Automatically notify support

Yes

Alert Category

Critical - Hard Disk drive

SNMP Trap ID

5

CIM Information

Prefix:

PLAT

ID:

0176

User Response

1. Make sure that the RAID adapter firmware and hard disk drive firmware are at the latest level.

2. Make sure that the SAS cable is connected correctly.

3.

Replace the SAS cable.

4.

Replace the RAID adapter.

5. Replace the hard disk drive that is indicated by a lit status LED.

•

806f060d-041fffff : Array [ComputerSystemElementName] has failed. (Drive 31)

This message is for the use case when an implementation has detected that an Array Failed.

May also be shown as 806f060d041fffff or 0x806f060d041fffff

Severity

Error

Serviceable

Yes

Automatically notify support

Yes

Alert Category

Critical - Hard Disk drive

SNMP Trap ID

5

CIM Information

Prefix:

PLAT

ID:

0176

User Response

1. Make sure that the RAID adapter firmware and hard disk drive firmware are at the latest level.

2. Make sure that the SAS cable is connected correctly.

3.

Replace the SAS cable.

4.

Replace the RAID adapter.

5. Replace the hard disk drive that is indicated by a lit status LED.

Appendix A. Integrated management module II (IMM2) error messages

687

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

IBM BladeCenter PN41 Problem Determination And Service Manual preview
BladeCenter PN41
Brand: IBM Pages: 88
MISUMI IP-004S User Manual & Installation Manual preview
IP-004S
Brand: MISUMI Pages: 18
Supero SUPERSERVER 5014C-MT User Manual preview
SUPERSERVER 5014C-MT
Brand: Supero Pages: 112
IBM 419452u - Servers System X3250 M2 Xeon... Installation Manual preview
419452u - Servers System X3250 M2 Xeon...
Brand: IBM Pages: 84
Fujitsu PRIMERGY TX140 S2 Operating Manual preview
PRIMERGY TX140 S2
Brand: Fujitsu Pages: 86
Fujitsu PRIMERGY TX150 S3 Options Manual preview
PRIMERGY TX150 S3
Brand: Fujitsu Pages: 95
Fujitsu PRIMERGY TX150 S6 Options Manual preview
PRIMERGY TX150 S6
Brand: Fujitsu Pages: 118
Fujitsu primergy TX150 User Manual preview
primergy TX150
Brand: Fujitsu Pages: 305
Fujitsu PRIMERGY TX150 S6 Operating Manual preview
PRIMERGY TX150 S6
Brand: Fujitsu Pages: 127
Fujitsu PRIMERGY TX140 S2 Upgrade And Maintenance Manual preview
PRIMERGY TX140 S2
Brand: Fujitsu Pages: 332
Fujitsu PRIMERGY TX150 S4 Options Manual preview
PRIMERGY TX150 S4
Brand: Fujitsu Pages: 97
Fujitsu PRIMERGY TX150 S7 Operating Manual preview
PRIMERGY TX150 S7
Brand: Fujitsu Pages: 120
Fujitsu PRIMERGY TX140 S1p Datasheet preview
PRIMERGY TX140 S1p
Brand: Fujitsu Pages: 9
D-Link DPR-2000 Quick Installation Manual preview
DPR-2000
Brand: D-Link Pages: 40
Canon imagePRESS Server G200 Configuration And Setup preview
imagePRESS Server G200
Brand: Canon Pages: 98
Canon imagePRESS A3200 Installation And Service Manual preview
imagePRESS A3200
Brand: Canon Pages: 192
Canon ColorPass-Z7400 Configuration Manual preview
ColorPass-Z7400
Brand: Canon Pages: 210
Gigabyte R272-P32 User Manual preview
R272-P32
Brand: Gigabyte Pages: 86

Brands by name

Popular brands

Load more brands