manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

SAS/SATA
power cable

Figure 69. SAS power cable routing

Step 13. If you removed any fans, install them.

Step 14. Insert the hard disk drives and the fillers the rest of the way into the bays.

If you have other devices to install or remove, do so now. Otherwise, go to “Completing the installation” on
page 136.

Installing a 16 x 2.5-inch Hot-Swap HDD Assembly Kit with Expander
for 12Gb RAID

Use this information to install a 16 x 2.5-inch Hot-Swap HDD Assembly Kit.

You can install a System x3650 M4 16 x 2.5-inch Hot-Swap HDD Assembly Kit with Expander for 12Gb. See
http://www.lenovo.com/ serverproven/ for a list of supported optional devices. To order a 16 x 2.5-inch
Hot-Swap HDD Assembly Kit with Expander for 12Gb RAID,contact your sales representative or reseller.

The 16 x 2.5-inch Hot-Swap HDD Assembly Kit with Expander for 12Gb RAID contains the following
components:

• One expander

• One backplane connection cable

Chapter 2

.

Installing optional devices

85

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

Supermicro SuperServer E102-9W-C User Manual preview
SuperServer E102-9W-C
Brand: Supermicro Pages: 103
HPE 3PAR StoreServ Service And Upgrade Manual preview
3PAR StoreServ
Brand: HPE Pages: 174
Grafenthal R2210 S2 User Manual preview
R2210 S2
Brand: Grafenthal Pages: 99
Advantech EKI-1511X User Manual preview
EKI-1511X
Brand: Advantech Pages: 76
Advantech ASMB-781 User Manual preview
ASMB-781
Brand: Advantech Pages: 92
Air Live WFP-101U v2 Quick Start Manual preview
WFP-101U v2
Brand: Air Live Pages: 87
Gigabyte G492-ZD0 User Manual preview
G492-ZD0
Brand: Gigabyte Pages: 152
Multitech SocketEthernetIP EN60601 Brochure & Specs preview
SocketEthernetIP EN60601
Brand: Multitech Pages: 2
Silicon Graphics 1200 User Manual preview
1200
Brand: Silicon Graphics Pages: 62
Silicon Graphics Altix XE340 User Manual preview
Altix XE340
Brand: Silicon Graphics Pages: 70
RGB Spectrum QuadView LES290A Quick Start Manual preview
QuadView LES290A
Brand: RGB Spectrum Pages: 7
Supero SBA-7142G-T4 User Manual preview
SBA-7142G-T4
Brand: Supero Pages: 76
Intel SE7230NH1-E Tested Hardware And Operating System List preview
SE7230NH1-E
Brand: Intel Pages: 19
Planet ICS-2200T Quick Installation Manual preview
ICS-2200T
Brand: Planet Pages: 16
Inspur OS Installation Manual preview
OS
Brand: Inspur Pages: 276
CAAS Audio DAS User Manual preview
DAS
Brand: CAAS Audio Pages: 27
Oracle SPARC T8-4 Service Manual preview
SPARC T8-4
Brand: Oracle Pages: 204
Oracle EXADATA X5-8 Service Manual preview
EXADATA X5-8
Brand: Oracle Pages: 278

Brands by name

Popular brands

Load more brands