Lenovo x3650 M4 BD 5466 Installation And Service Manual Download Page 435

Page: 435 / 1222

Info

Serviceable

Automatically notify support

Alert Category

System - IMM Network event

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0139

User Response

Information only; no action is required.

•

80010002-0701ffff : Numeric sensor [NumericSensorElementName] going low (lower non-critical)

has asserted. (CMOS Battery)

This message is for the use case when an implementation has detected a Lower Non-critical sensor
going low has asserted.

May also be shown as 800100020701ffff or 0x800100020701ffff

Severity

Warning

Serviceable

Yes

Automatically notify support

Alert Category

Warning - Voltage

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0476

User Response

Replace the system battery.

•

80010202-0701ffff : Numeric sensor [NumericSensorElementName] going low (lower critical) has

asserted. (CMOS Battery)

This message is for the use case when an implementation has detected a Lower Critical sensor going
low has asserted.

May also be shown as 800102020701ffff or 0x800102020701ffff

Appendix A. Integrated management module II (IMM2) error messages

423

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3650 M4 BD 5466

Reviews:

Related manuals for x3650 M4 BD 5466

Brands by name

Popular brands

Lenovo x3650 M4 BD 5466, Installation And Service Manual

Search results

Summary of Contents for x3650 M4 BD 5466

Reviews:

Related manuals for x3650 M4 BD 5466

Brands by name

Popular brands